Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Harmonic Vibration
User Name
Password
lost password?   |   register now

Thread: Harmonic Vibration Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-20-2011 08:55 AM
S10xGN
Quote:
Originally Posted by RoadSide Dan
Well, it looks like the pinion ange is 3/3, but 3 down and another 3 down--ugh. The front u-joint is slinging grease and is fighting back. I've only been able to drive it at 20-30 mph thus far. The body work looks good, but...
That could be your problem. When I built my Maverick, my "cohorts" told me to weld the spring perches with the nose at 6 down because of the leaf springs. Obviously, they are racers and not street drivers. After realizing that my Caltrac bars don't allow any pinion rise, I ordered a set of 8 shims (from an offroad place) to counteract my negative pinion angle. I now have my trans at 4 down and the pinion at 2 up, and all is good!

Russ
08-20-2011 12:56 AM
RoadSide Dan
harmonic vibration

Well, it looks like the pinion ange is 3/3, but 3 down and another 3 down--ugh. The front u-joint is slinging grease and is fighting back. I've only been able to drive it at 20-30 mph thus far. The body work looks good, but...
08-09-2011 11:23 AM
KMatch There is no 1 size fits all. You need to measure the angle at the rear of the transmission of engine tilt. If it's 3 degrees, the pinion must be tilted up 3 degrees. 2 for 2, and so on and some will be good with a degree or so of difference and others, not so much. Another thing, never run a driveshaft at zero degrees at either end (driveshaft straight) - this will kill u-joints as the needles will pound grooves in everything.
08-09-2011 08:50 AM
S10xGN U-joints are designed to handle some amount of misalignment. Do you trust whoever built the driveshaft? I'd start by verifying the phase angles, both sets of "ears" should be in exactly the same plane...

Russ
08-09-2011 03:46 AM
RoadSide Dan
Harmonic Vibration

What's the correct pinion angle for a 9" Ford rearend?

My '53 Chevy 3600 had a 9" Ford offset rear end and a two piece driveshaft. It ran pretty smooth at that time.

While doing a frame-off restoration, I decided to convert to a single piece driveshaft and set the rearend angle more in line with the driveshaft. Converting to a single piece driveshaft and resetting the pinion angle to 3 degrees has resulted in a bad harmonic that starts about 35 mph and increases with speed.

Help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:57 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.