Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> '65 chevelle 2dr post headliner moldings?
User Name
Password
lost password?   |   register now

Thread: '65 chevelle 2dr post headliner moldings? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-22-2011 06:52 AM
DanTwoLakes The sail panel blanks will have the holes for the clips already in them. All you need to do is put in the clips, line up the clips with the holes, and pound them in.
08-21-2011 08:47 PM
lngliv3 Thanks again for the info DTL, i see the clips hanging in the sail panel area, now to just find the right sail panel blanks. The ones you showed a picture of are similar to the ones ive been finding as well. The only problem is, none of the blanks have an area to hold these clips in the board...? None the less, youve great help, thanks again.
08-21-2011 06:55 PM
DanTwoLakes From your pictures, it appears that your car has separate sail panels. Your headliner goes down as far as that horizontal metal bar which should have cardboard in the center to staple or tack to. The sail panel is held in place with panel clips to cover the rest of that area. The rear of the sail panel is open, and the fabric is glued around the rear window opening. There are still two panel clips sticking out on the driver and passenger side sail panel area, just below the horizontal metal strip. I did a '69 Camaro a couple months ago that was the same way. I can't see any way to attach windlace around that edge next to the rear side windows. That has me stumped. It almost looks like there should be some rubber trim or something like it there.
You're going to have to find a Chevelle that has a headliner in it and take some more pictures.

I did some internet checking, here are the sail panel blanks:
CLICK HERE
08-21-2011 05:11 PM
lngliv3 DTL,
Thanks for the reply, and after reading some of your other posts, its obvious you know your stuff! Please allow me to pick your brain a little further. I brought my car to my home garage today to get some pictures of the areas im looking at. I can see what you mean about the windlace going all around the front door jam pinch weld areas. The spots that are throwin me off are the "tack" strips that go above the rear quarter glass, down around the sail panels. At this point, Im thinkin another short piece of windlace will do the trick, so now im focused on the sail panels...what holds them thin wafers to the wall? If you can see that "bar" going across the sail panel area? Do these hold the panels some how? Or are they just a tack area for the headliner behind the sails....?
08-21-2011 09:15 AM
DanTwoLakes The windlace goes around the door and/or window openings. There are gripper strips that screw in over the door and/or window openings, and the headliner is tucked under the gripper strips (which fit snugly up next to the windlace) to complete the installation. If you don't have gripper strips, you will need to find some or make some. Look at this thread which should explain things for you: HEADLINER TUTORIAL If you need to make gripper strips (headliner retaining strips) just ask.
08-20-2011 03:48 PM
lngliv3
'65 chevelle 2dr post headliner moldings?

Guys, Does anyone know what kind of molding goes along the sides of the headliner in a 65 chevelle 300 deluxe (2 dr post)? I have the rear window/windshield strips, but not even OPGI can tell me what seals the headliner along the side windows from the windshield back to the sail panels and down to the rear package tray in a '65. Some say its a piece of windlace? Plaese help, this is the only thing holding me up from starting my interior!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.