Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Looking for HELP.. Major Vibration
User Name
Password
lost password?   |   register now

Thread: Looking for HELP.. Major Vibration Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-24-2011 05:00 PM
trees Another thing to check is proper servicing and torquing of the front wheel bearings. The out of balance condition of the tires could easily have damaged the bearings, especially if they were not properly installed. Additionally, with the MII front end, there are brake kits out there that require different bearings, spacers and dust seals. If the instructions were not followed correctly, you could get the symptoms you are describing.

Trees
08-24-2011 08:45 AM
Tony@AirRideTech
Quote:
Originally Posted by S10xGN
On the driveshaft...check the obvious first. Look at where the yoke goes into the transmission, there should be 3/4" to 1" maximum space between the yoke and transmission seal. Any more than that can cause the yoke to wobble. Suspension must be loaded for an accurate check, best done on a "drive on" rack.

Russ
And thats what she said
08-24-2011 08:35 AM
S10xGN On the driveshaft...check the obvious first. Look at where the yoke goes into the transmission, there should be 3/4" to 1" maximum space between the yoke and transmission seal. Any more than that can cause the yoke to wobble. Suspension must be loaded for an accurate check, best done on a "drive on" rack.

Russ
08-24-2011 07:27 AM
Tony@AirRideTech if the vibration was near the same and at same speed after two separate tire balances than I dont know if I would bother looking at the tires much more. The only other thing to look at would be if the wheel or tire is out of round. In that case you can actually trick a machine into balancing it but it still will not make it round again if you get my meaning.
What this really sounds like to me is drivline angles or as mentioned above the driveshaft being out of balance or out of phase. That is where I would start... pull the driveshaft and take it to a competant shop to check for balance, phasing and correct length. Next, while the drive shaft is out you need to check the trans tailshaft and the pinion yoke for correct pinion angle... my money is on bad pinion angles
08-24-2011 05:54 AM
timothale
steering wheel shake

can you switch the wheels front to back and do a test drive and see if the vibration changes. can you tell if there is more or less feel in the steering wheel. depending where the tires are installed ,Has the front alignment been checked ?, A bad u joint will cause a vibration even though you can rotate the drive shaft by hand and not feel any wear. but as Dave suggested check out angles and phasing first,
08-24-2011 05:32 AM
Irelands child That drive shaft - most likely it was made up to fit the transplanted driveline. Besides balance, and they do have to be balanced after assembly, the yokes have to be "timed" correctly and totally in phase. The solid cup retaining sides must line up exactly with the opposite end. They also need to welded up correctly. Rather then me try to blunder through an explanation, here is some good reading

Dave W
08-23-2011 08:51 PM
1brewmaster1
Reply to question

I had a drive shaft go bad once and I felt the vibration in the seat of my pants. This vibration causes the steering wheel to go crazy, shaking and osculating left to right.
08-23-2011 07:58 PM
awert I'm no expert, but your going to have to narrow it down some, there are lots of things that could be faulty, with all the mods.....I had a out of ballance drive shaft that did that, took many weeks to find, had all the PRO's fooled....are you sure it is comming from the front wheels???
08-23-2011 07:07 PM
1brewmaster1
Looking for HELP.. Major Vibration

Good Day All...

Kind of new to the forum and real new to Hot Rods. I recently picked up a '51 Chevy 3100 that had been Resto Modded with a 350/350, 700r4, Mustang II front end (after market), after market tilt steering Chevy 10 bold rear end, has 245-40-18 Nitto 555's with KMC wheels and drop spindles which leaves the truck with a nice rake. When I picked up the truck I was advised by the owner/builder that there was a vibration at about 55 MPH to 65 MPH and he thought it was the tires needed to be balanced. When I got home the vibration was so bad that I immediately had the tires balanced. The garage said that 3 of the four tires would not balance correctly as they required upwards to 13 onces on each of the three tires/wheels. They STATIC balanced the tires and sent me on my way.

Today I went to another garage that had a super balance machine and they indicated that they will be able to tell if the tires or wheels are bad and if they can be balanced. All four tires balanced correctly after de-flating and spinning the tire 90 degrees on the wheel and minimal weight was put on each wheel and I am on my way again.

First thing I did was go on the interstate and brought it up to 60 MPH and found the vibration alive and well.

Can anyone suggest something to look at that may cause this steering wheel shaking vibration. The truck has only 1200 miles on all of the parts and everything appears to be tight.

Thanks for your input...

Richard

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.