Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> How to improve my cabinet blaster
User Name
Password
lost password?   |   register now

Thread: How to improve my cabinet blaster Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-12-2011 09:05 AM
JohnnyK81 Crap, I was banking on nobody owning the pot!

I just personally find there are better compressors for less money out there. I was going to buy that compressor actually!
09-11-2011 11:42 PM
evintho OK, pot stirred! I own the SS5N5. Same compressor listed except for an 80 gal tank. Bought it new from TSC in 2006. It gets used almost daily and I haven't had a problem with it in 5 years! I've heard that some have had issues with the compressor motor but I've had none. Maybe I'm just lucky. Anyhow, great compressor. Runs my 90lb pressure pot blaster, blast cabinet, air tools and anything I can throw at it!
09-11-2011 11:30 PM
JohnnyK81 And, just to stir the pot.. DON'T buy that compressor.. Trust me, I was going to.
09-09-2011 06:54 AM
timothale
blaster

My compressor is big enough, My home made cabinet,big enough to blast a rear end, has a sloping bottom and reuses the media with the bottom suction hose. I have read here on HR to get your bucket of media at least as high as the gun so it doesn't have to lift the media up the hose. I usually pressure wash and solvent wash everything so I don;t get globs of greasy mud in the blaster.
09-09-2011 06:13 AM
OneMoreTime Media choice has a big effect as well..I use vitro grit which is crushed glass and that stuff cuts well at lower pressures and volume..Makes my little spot blaster work just fine..

Sam
09-03-2011 09:49 PM
evintho It doesn't sound like you have much of a compressor. That's your first major hurdle. Upgrade to this, as a minumum. It's all about the CFM when it comes to blasting. Once you have a compressor of this size, unless you're running a business, it's probably the last one you'll ever need!

http://www.tractorsupply.com/ingerso...ressor-3301332

Here's a couple of suggestions for a good blast cabinet. CL is loaded with good stuff!

http://sanantonio.craigslist.org/bfs/2541888687.html

http://austin.craigslist.org/tls/2566094831.html

Then of course there's the Barrel Blaster..................

http://www.barrelblaster.com/
09-03-2011 06:48 PM
1badLemans Hey Mike I was having the same problem with my cheap blaster that I bought from harbor freight. It turned out I didn't have enough CFM out of my compressor that I had. My home one was only putting out 6.5cfm. I took my blaster to my buddys shop which had an industrial type compressor putting out well over 20cfm and man did it BLAST. Then I NEEDED to run a vacuum to actually let me see in the cabinet. Somtimes flow is also slowed down by the type of media you're using. I like baking soda but it doesn't get rid of rust just paint and filler. But I had almost not flow with some plastic media I first used. Good Luck man
08-27-2011 04:22 PM
mike69
How to improve my cabinet blaster

Guys,

I'm blasting some parts in my cabinet blaster and the slow pace is killing me. I have an inexpensive floor based suction blaster from Northern Tool. I've already gone through troubleshooting it and I think it's just slow because it's cheap. I'm pretty sure I read a post some time ago about how you can add a pressurized tank type blaster to a standard suction blaster to improve its efficiency but now I can't find that post. Is it possible to do something like that? I don't do that much blasting, but if I can't get this thing to improve how it is working I'm going to go crazy! If there is nothing I can do to improve this thing can someone recommend a good affordable (under $1,500) cabinet blaster? Thanks.

Mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.