Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> old double hump heads
User Name
lost password?   |   register now

Thread: old double hump heads Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-20-2002 12:37 PM
oldcarguy85 these heads are great... i got teh 462s on my 327 and they are awesome. wth the 2.02 valves man they are sweet. anyway the brackets are no problem. go to any local auto parts store look in the mr, gasket crap. tehy have a litte pice that is attached by the header bolts and then u use an f braket for the alternator. then u can use any p/s pump off of liek any old chevy pickup that mounted down low on the two holes near the balancer. then a/c is kinda a challenge. i fabbed up a brakcet cause i couldnt; afford the march performance bracket. but those ore ncie brackets that march has and they ave them ofr eveyrhting.
06-20-2002 09:08 AM
tjk2000us2000 What casting number are they? I had a pair of 461X( the X is only on the underside) heads on a 71' 350. They seemed to work real well for me. As for the brackets I didn't have a problem finding something that worked for me. For the alt. the bracket bolted to the water pump and intake I think. I can't remember about the power steering but it worked.

06-19-2002 09:28 PM
30coupe Also, you'd better plan to have hardened valve seats installed. The old heads are made for leaded gas. They may perform for a while, but it won't take long running unleaded gas and the valves will begin to recess in the heads. Unleaded erodes the valve seats pretty quickly.

06-18-2002 06:12 PM
Paco You might pick up any streetrodder magazine and check out Billet Specialties brackets. They are also on the web. Alan Groves is another source for steel brackets,but I am not for sure they can be mounted without the use of the holes in the head. The Billet Specialties brackets mount off the water pump and the first two intake bolts on either head. They are polished billet aluminum and look great. They will allow for the alternator and A/C compressor. I use a Sanden compressor, don't know if a factory stock GM compressor will work or not.
06-18-2002 06:01 PM
1BAD80 Check the valve to piston clearance before you put it together. Or you mite have some bent valves and push rods. Most later pistons dont have enough clearance for the 2.02 valves plus any good lift cam.
06-18-2002 03:10 AM
Tom I have several sets of those heads and found no problem useing them the only fabrication I had to do was the alternator bracket off the water pump but forget about the A/C. yes these heads will boost the horses and compression on your 84 350
06-17-2002 03:23 PM
chale24088 I have a 84 Z28 camaro with a 350 that has original heads I heard that the double humps would give me a few more horses. Please tell me if I am wrong...
06-16-2002 06:16 PM
helrazr3 i dont know what your using them for but if you can get the original exshaust manifolds the holes are there. those heads are mid 60s or earlier. there are also a few aftermarket companys that make brackets fof your conversion i cant remember the names right now but ive seen the adds in streetrodder and rod and custom magazines.good luck
06-16-2002 09:55 AM
old double hump heads

I have a set of old double hump heads that do not have the holes bored for the alternator and the power steering pump. What is the best option for me ? To try to have them bored or have special brackets made?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:00 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.