Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Muncie 4 speed
User Name
Password
lost password?   |   register now

Thread: Muncie 4 speed Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-15-2011 12:26 AM
TimoFinn Here`s a good site to look for the differences in muncies

http://www.5speeds.com/muncie2.htm
09-14-2011 06:54 PM
2old2fast I'm probably wrong about this ,but weren't both the m21 & m22 available w/ either the 2.56 low or the2.20 low [wide ratio-close ratio] , other than that their pretty much identical except foe countershaft size !?!?

dave
09-14-2011 05:44 PM
solidaxel Go with the 3:73, it will relieve more "STRESS" !!
09-14-2011 05:38 PM
DanBoyd Huge thanks to everyone. I went with the M21. You all have some great points, plus M21 is rebuild and trust the gentlemen that had it. Unsure of clutch and pressure plate to go with. Also flywheel. I have 89 5.7 engine. I live in a tight curve hilly terrain, do you say 3:43 or 3:73? Mileage at these gas prices means a lot but it is not going to be driven on the interstate. The car is just my stress relief car. I love a 4 speed and curves. The powerglide just seems lame with the current setup.
09-12-2011 01:24 PM
AutoGear All things being equal (and they never are) an M21 will be marginally stronger than the M20 and we're talking percentage here. The farther 'away' from 1:1 you get, you lose some strength.

Total Gear Reduction is essentially the mechanical advantage of the geartrain to move the car (first gear times the axle ratio).
The reality is you will have a total gear reduction of '8.2' with the M21 and 3.73s (2.2 x 3.73) Thats a pretty soft 1st gear. Use the M20 and 3.73s (2.5 x 3.73) This will give you a TGR of 9.3. The vaunted M22 and 4.11s (2.2x4.11) was 9.04.
This is all assuming both available units are in good shape. I would also prefer a 1" countershaft over the 7/8" countershaft for strength and for parts availability.

Also note that if your car was originally 32 spline, a 27 spline setup (or vice versa) may cause shifter-to-console interference. AND pre 1969 units use a stud mounted linkage on the sidecover and reverse levers; 70 and later units use a bolt-on type. These do not mix and match well.
None of these problems are insurmountable as long as the unit is in good repair.
09-11-2011 10:55 PM
solidaxel Save your money on the rear end and get the best of both worlds, go for a Tremac TKO 500 and it will work great with your 2:73's, just right 1st and super 5th OD
09-11-2011 10:43 PM
willowbilly3 What I base it on is some really old memorys of rebuilding an M21 I had in my 64 Cutlass. My classmate at auto tech college was in transmission class and doing the work. He also had an M20 apart and the cluster shaft in it was smaller when we were comparing parts. But then a 40 year old memory might not be accurate.
09-11-2011 10:36 PM
WDCreech
Quote:
Originally Posted by willowbilly3
I'd go with the M21, it's a little stouter.
willowbilly, What do you base your opinion on? The M20 and M21 are the same transmission except for gear ratio. The M22 was stouter than either, but I don't think there is any difference between the M21 close ratio and the M20 wide ratio.
09-11-2011 10:07 PM
willowbilly3 I'd go with the M21, it's a little stouter.
09-11-2011 07:54 PM
DanBoyd Thank you very much
09-11-2011 07:02 PM
poncho62 Yes, you will need a later flywheel.....snout on the 1 piece sael crank is different than the 67 one....

As for the tranny, if you are going with the steeper gears, go with the M21.....If staying with a highway gear, the M20 would be better as it has a wider gear ratio in the gears.
09-11-2011 05:25 PM
DanBoyd
Muncie 4 speed

I need advise badly. I have been stressing over an automatic 67 Camaro to a 4 speed conversion. I know I want the 4 speed. I have the choice of M20 or M21, 2 guys are standing by waiting on the phone to ring. Unsure which one to purchase and use.

My setup is 1989 355 ci with one piece seal. Rear end is a 2:73 at best (airplane gears). Going to change the rear end to 3:43 mostly or 3:73 being second choice. The car is not a daily driver, nor an interstate trip car. Will be driven for fun and sunday drives. I like take off red light to red light. Son llooks hot shots. so do I.

Which transmission should I choose and why?

Which type of flywheel and clutch and pressure plate? Will 1989 350 flywheel work because I don't think 1967 flywheel bolts on the same unsure.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.