Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Best Place for Temp Sensor for Electric Fan?
User Name
Password
lost password?   |   register now

Thread: Best Place for Temp Sensor for Electric Fan? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2011 05:30 AM
75gmck25 Your engine temp at the manifold will run at the thermostat temp (e.g., 195) or about 5 degrees higher (195-200) if everything is working right. You want the fan to kick in if it gets to about 5-10 degrees higher than the thermostat temp, and to kick off when it gets about 5-10 degrees lower than the thermostat. With a 195 thermostat I think I would have the fan kick in at 200 and turn off again at about 185.

I've run my temp sensor mounted on the passenger side head fitting and on the intake manifold, and did not find a lot of difference in measured temp. I think the measured was always within about 5 degrees.

Bruce
09-19-2011 05:09 AM
willowbilly3 On the last system I designed (small block Ford) I put it in the water passage on the intake. It's been a while but I think I used a fan-stat from a chrysler application. It came on much cooler than the Ford and Chevy ones.
09-18-2011 10:43 PM
solidaxel I use a 195* switch in the passenger head and a180* Robert Shaw high flow thermostat in the manifold. The thermo. keeps the water at 185* until it needs some cooling and then it cycles off, only on when needed.
09-18-2011 09:09 PM
trifivefan Thanks, guys for all the great advice. If I use a sensor on one of the cylinder heads, what temp sensor should I get? If this setup will indicate hotter, should I go with a 190 degree? With the sensor on the lower hose, like Ogre suggested, would the temp sensor be of a lower rate, say 180 degrees?
09-18-2011 11:39 AM
ogre you wouldn't want a radiator fan sensor in your engine, it would always run when the motor got up to temp.

i used a short piece of exhaust pipe in my lower radiator hose. i welded half of a 3/8 pipe coupling in it for the fan sensor. also weld on a ground stud to ground the tubing and sensor.

my thoughts for using the lower hose? i figured to let the radiator do it's job cooling coolant, if it comes out too hot; then turn the fan on.

if you put in the thermostat housing or the upper hose, your fan will run as soon as the thermostat opens. even if there is ice in your radiator.
09-18-2011 10:25 AM
302 Z28 A temp sensor in the head will indicate hotter than one in the T-stat housing by as much as 15 degrees.

Vince
09-18-2011 06:57 AM
Bryan59EC Another option would be to
use a sender that will fit in the radiator petcock hole.

You would have to use a sender that comes on real low tho.

on @ 180
off @ 160

Could also remove the intake (not absolutely necessary) and drill and tap for another sender.

I'm sure there is a boss somewhere on the intake for an additional hole.

I just too a brand new manifold in to get drilled for a fan switch on my 66 Elky
09-18-2011 06:42 AM
EOD Guy depending on your sender you can tap into it and control the gauge and the fan controller. Dakota digital does this type setup.
09-17-2011 08:32 PM
solidaxel I assumed you did not want to use the plugged holes in the head one by cylinder 6 & 8 and a bit hotter on the other side by cylinder 1 & 3.
09-17-2011 07:03 PM
123pugsy No holes in the heads that can be used?
I know my temp sender is there.
09-17-2011 05:56 PM
solidaxel tRY A THERMOSTAT housing for a 78 chevy pick up
09-17-2011 05:25 PM
bubbahotep They make waternecks (where the radiator hose connects) with temp gauge holes in them. Im not sure if they make pretty ones but Ive used cast ones in the past
09-17-2011 05:16 PM
trifivefan
Best Place for Temp Sensor for Electric Fan?

My streetrod only has one opening on the intake manifold for a temp sending unit. If I use that one for the temp gauge, I don't have another for the electric fan. What can I do? I have a 350 chevy. Any ideas would be appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.