Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> GM type 2 pwr strng pump- suction fitting?
User Name
Password
lost password?   |   register now

Thread: GM type 2 pwr strng pump- suction fitting? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-24-2011 08:38 PM
hafjag
Press fit suction tube- GM type 2 pumps

It turns out the suction tube is a press fit in the bottom of the pump suction opening.
Good news- A suction tube is available from your Chevy dealer- its for a "late model Corvette", part # 26006074. I called the local Chevy dealer, and it's available. Bad news- it lists for $42. That's more than I paid for the pump! they wanted $34. Too rich for my blood. I used a brass 3/8" npt X 5/8" hose barb ($3.05 at Lowes). Half inch hard copper tubing fits into the back of the hose barb- I soldered it in- and the 3/4" projection I left pressed into the pump suction opening very firmly. I had to grind the 3/8npt threads down to fit into the top part of the pump opening. I used PC7 to lock the brass fitting into the pump. ( I'm not planning on taking it apart)
Sooo...
There you have it. Good to go. Total cost $3.22, with tax.
09-19-2011 09:13 AM
enjenjo In this type of situation, I have turned a custom fitting on the lathe that duplicates the end on the reservoir, that will accept a hose on the other end. You would then have to figure out how to hold it in place.
09-18-2011 10:21 PM
hafjag
GM type 2 pwr strng pump- suction fitting?

I am in the process of installing a hydro boost brake system in my 350 chev powered (turbocharged) 68 XKE Jag coupe (no power steering). I started with the 86 Cavalier pump (attached reservoir) but there wasn't enough room for the reservoir, so I'm going with a remote reservoir setup.
Now here's my problem-I'm trying to figure a way to connect the suction hose to the pump. the attached reservoir has an o-ringed projection that enters the pump. When I remove the reservoir, there's nothing to connect the suction line to.
Any suggestions?
Remote reservoir versions of this pump are identical to the attached reservoir versions, except that they have a suction hose connection. I've checked the internet, and cant find any info regarding any type of fitting that I might use to connect the low pressure suction line to my pump.
I may have to purchase a similar hose connection equipped pump, unless I can figure a way to connect the suction line to my pump.
Any suggestions would be appreciated.
Thanks in advance for your help.
PS-this is my first real post, so hello all!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.