Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Not sure where to start on this one frame mounted master cyl
User Name
Password
lost password?   |   register now

Thread: Not sure where to start on this one frame mounted master cyl Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-19-2011 08:59 PM
cucumber1949 No, don't have a photo of my setup, but I took a look at the website I referenced in my link above and found their instruction manual:

http://www.spiritcars.com/images/pdf/AssemblyManual.pdf

If you look on pages 3 and 9, I think you'll see how they do it on their vehicles.

Just as an aside, I notice they put a proportioning valve on the line to the front brakes which is probably not correct for anything other than something like a T with very slender tires up front - typically don't see those anymore due to ride and wear issues.

Good luck to you.
09-19-2011 08:42 PM
Studedean got a photo? im consifering skipping the booster to save room, hate to though. its good ot hear I can extend and put the pedal assy in front of the cross member and the unit behind it
09-19-2011 07:07 PM
cucumber1949 My T-Bucket has much the same setup as you're trying to figure out. The MC mount is aft of the trans crossmember, the pedal goes up through the floor, pivots on a stud mounted to the frame, and actuates a pushrod which is made to reach the MC. If I wanted, there is enough room for a booster but the T is light enough and has enough pedal ratio that it is not needed. The setup I'm using is similar to this:

http://shop.spiritcars.com/Brakes/Br...y/prod_26.html
09-19-2011 03:55 PM
35terraplane
Master cyl

Quote:
Originally Posted by Studedean
I was advised on and bought a frame mounted master cylinder and power booster. My setup is commonly used on rat rods from what im told. Ive got the brake pedal coming straight out of the front of the booster and it appears its supposed to go up through the floor of the cab.
my issue isnt really not understanding on how to get it together or even how to run the lines, everything is disk.
My issue is this there appears to be no room to put this in as designed. its a studebaker body (not really much metal), and an s10 frame. When I place the whole unit against the frame where it looks like it would be the best to get the pedal up through the floor. ive got about a foot ahead of the trans cross member, and the master/booster wont fit. if I go back behind the trans cross its to far away from the floor for the pedal arm to make to. Id love to firewall mount but the header, transcross, pretty much everything is in the way. cant tell you how many times ive layed under there trying to figure out how to make it happen. any suggestions?
That is one reason we say use the frame the car came with, or build your own. We can't see what you have to deal with, post some pictures, someone might have some ideas or you might have to use a different setup.

Bob
09-19-2011 01:53 PM
Studedean
Not sure where to start on this one frame mounted master cyl

I was advised on and bought a frame mounted master cylinder and power booster. My setup is commonly used on rat rods from what im told. Ive got the brake pedal coming straight out of the front of the booster and it appears its supposed to go up through the floor of the cab.
my issue isnt really not understanding on how to get it together or even how to run the lines, everything is disk.
My issue is this there appears to be no room to put this in as designed. its a studebaker body (not really much metal), and an s10 frame. When I place the whole unit against the frame where it looks like it would be the best to get the pedal up through the floor. ive got about a foot ahead of the trans cross member, and the master/booster wont fit. if I go back behind the trans cross its to far away from the floor for the pedal arm to make to. Id love to firewall mount but the header, transcross, pretty much everything is in the way. cant tell you how many times ive layed under there trying to figure out how to make it happen. any suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.