Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> piston rings 1/16 vs 5/64
User Name
Password
lost password?   |   register now

Thread: piston rings 1/16 vs 5/64 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-22-2011 12:47 PM
lg1969 Cobalt327 is correct on the rings. The thinner ring are for racing to reduce friction and reduce the heat it generates at high RPM. It's used in NASCAR racing. The problem is you will get more blow-by and consume more oil if it is used for street use.
09-22-2011 12:54 AM
67-4-fun thank you again for the info.. its a good education on this, maybe minor, but it all adds up in the end.. so thanks again, I will read the article
09-21-2011 12:52 PM
cobalt327 Convention holds that thinner rings are "racing" and thick rings are "street". But what was thin ten years ago is considered thick today. It's not unusual for high end builds to use 1/16" rings for a street engine, but there's a lot to consider if you go that route and cylinder finish and roundness are key- plan on a torque plate hone (which should be done anyway).

The link below is to an '09 article in HR mag on rings. I looked at it previously and saw no glaring inaccuracies, if you want to give it a look-see:
http://www.hotrod.com/techarticles/e...h/viewall.html
09-21-2011 12:48 PM
ap72 I mostly used the thicker rings as the pistons and rings are cheaper, BUT almost all major car companies are trending towards thinner rings...

Also keep in mind bore finish, piston finish, and ring material/finish is not what it was 30 years ago.
09-21-2011 12:28 PM
67-4-fun thank you for the info tech... that will help sum it up and give me a more idea on what to expect
09-21-2011 12:16 PM
techinspector1 I'm not sure if my information is bogus or not, but I'm told that the thicker ring will seal a little better due to more contact area on the wall, but is heavier and will produce less seal at high rpm's because the ring is too heavy to stay on the ring land, having a tendency to flutter. I'm told that the thinner ring will not seal quite as well at lower rpm's, but will hold its position in the land a little better and have less tendency to flutter at high rpm's due to the lighter weight.

I have no scientific data to back this up, so make your own choices based on what seems like it would work better for you. Most of the stuff I have built was street driven and I used the thicker rings.
09-21-2011 12:09 PM
67-4-fun
piston rings 1/16 vs 5/64

I know this has been discusses before, just trying to get more up to date info on using 1/16 piston rings vs a 5/64 the pros and cons, what can each handle? Reading ive found seems not to realy matter which to use but wounder if there is a neg side to using a smaller ring thickness, ive always been told to use a 5/64 ring, but like to try a 1/16 if i knew more about the usage of a smaller ring thickness..

thanks for your time
JP

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.