Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> trans. angle /pinion angle adjustments ?
User Name
Password
lost password?   |   register now

Thread: trans. angle /pinion angle adjustments ? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-24-2011 02:02 AM
SSedan64 Pinion Angle tips from Rossler's site >> http://www.rosslertrans.com/Pinion%20angle.htm

4-Links do have much less deflection than Leaf & Ladder type suspensions.
As 'Cobalt327' said, Bushing type affects the amount, OEM Rubber, Polyurethane & Aluminum.
09-23-2011 07:27 PM
cobalt327 Billy Shope’s site on suspension- http://www.racetec.cc/shope/

Whether or not there will be pinion rise on acceleration depends on a hoard of things, the basic rule of thumb still applies: Under acceleration you want there to be as close to a zero angle as possible. If that means a degree or two difference between the trans and rear end, then so be it. But there's no correct answer w/o testing, anyway.

There is going to be some deflection unless the links, chassis and all the pick up points are 100% rigid. In a street driven 4-link I'd expect there to be more not less deflection (urethane or rubber bushings instead of solid rod ends, for example) and if that's the case, there's more possibility of some angle being needed as opposed to no angle at all.

I don't know how anyone could discern the OP's intentions were to not drag race it by his post, but then I assumed anyone doing a back-halved Vega w/a front plate and 4-link w/a 9" rear end planned on using it, not just profiling w/it. It will help if the OP would elaborate on the chassis, power train, the 4-link and how it will be used.
09-23-2011 04:54 PM
Centerline
Quote:
Originally Posted by user151
What Cobalt said may be correct "under acceleration" but considering you have a 4 link and sound like you are not a racer or dragger, I would set the rear pinion up the same as the trans is down... 5 degrees.
X2
The ONLY time you want a negative pinion angle is if its a strip car. A four link wouldn't need negative anyway as the pinion angle won't appreciably change during acceleration like it does with leaf springs. For street driving you want to match the trans angle in reverse. Trans 5* down - pinion 4-5* up.

Centerline
HotRodsAndHemis.com

The most important things you learn are those things you learn AFTER you know it all. -- Chip Foose
09-23-2011 10:29 AM
user151 What Cobalt said may be correct "under acceleration" but considering you have a 4 link and sound like you are not a racer or dragger, I would set the rear pinion up the same as the trans is down... 5 degrees.
09-22-2011 05:17 PM
prostreet6t9 Keep in mind.... The 4-link will hold your pinion angle better than a stock set up.
09-22-2011 05:03 PM
cobalt327
Quote:
Originally Posted by rf9763
hello all, i under stand how to adjust pinion angle. i have a 4 link rear back halved ford 9 in setup.my question is ,my trans at the end of tail housing is 5 degrees down .do i set pinion angle at 5 degrees up for center to center and then lower pinion down 2-3 degrees? is that to much down on trans to make this work?i have driven car 50 60 mph and got small vibration from rear of car with this set up. this is my first 4 link and not sure about the trans angle. not much i can do to raise trans cause this is a vega. NO ROOM. lol. any advise or input would be great. thanks for your time and help.also motor plate in front and poly trans mount.
The idea is to have a 0 angle with the vehicle under power and the exact amount of drivetrain deflection will be different for every vehicle. That said, if you end up with -2 degrees static pinion angle, you should be OK due to the tendancy for the pinion to 'climb' the ring gear under acceleration.
09-21-2011 08:37 PM
rf9763
trans. angle /pinion angle adjustments ?

hello all, i under stand how to adjust pinion angle. i have a 4 link rear back halved ford 9 in setup.my question is ,my trans at the end of tail housing is 5 degrees down .do i set pinion angle at 5 degrees up for center to center and then lower pinion down 2-3 degrees? is that to much down on trans to make this work?i have driven car 50 60 mph and got small vibration from rear of car with this set up. this is my first 4 link and not sure about the trans angle. not much i can do to raise trans cause this is a vega. NO ROOM. lol. any advise or input would be great. thanks for your time and help.also motor plate in front and poly trans mount.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.