Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Q's on 454 marine block
User Name
Password
lost password?   |   register now

Thread: Q's on 454 marine block Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-27-2013 11:51 PM
NastyRat
Wet 454

There is difference in a marine Vs automotive. First of all marine blocks are 4 bolt mains, added piston to wall clearance, more than likely big port heads depending on hp rating 330 and up are the big ports, and they also have different cam grinds. they will use oil in a street application do to the added clearance. In a marine engine the block stay's much cooler than in a automotive application and the piston stays much hotter. That's why they and the extra clearance. Marine engines are set up to run at higher sustained loads at 3000 to 4800 rpm's at over 50% throttle and up to wot for long periods. Also cast with a higher nickle content.
10-15-2011 11:02 AM
bigalow I'm a MOPAR MAN and this is my first big chevy in a Hotrod- Excited.
They say "once you go Mopar you never go Chevy" But maybe its the otherway around??? HMMM?
10-15-2011 07:32 AM
bondo
Quote:
Originally Posted by bigalow
Is a marine block any different?
Ayuh,... The blocks are the same, they're just assembled differently...
10-15-2011 07:06 AM
bigalow thank you I will get a new rod plus a new torque cam.
Would a turbo 400 be a good choice for a trans??
Going in a 54 pickup w 3.23 gears
I have read the TH series trans's rob alot of HP 25%
10-14-2011 11:22 PM
scholman bigalow,

The engine doesn't know it is in a marine application.
The only thing to watch for is that after the sleeve is installed and bored out to match the other cylinders is that the cylinder/s next to the sleeve need to be honed straight.
Also check the connecting rod to see if it got a little bend in it. If it is bent replace it. I think I would just replace it when you have the new piston installed.
If you plan on running this engine in a street application then the camshaft will need to be changed also. The marine engine must produce horsepower as soon as the throttle is cracked open in order to propel the boat out of the water and onto "plane" with only the bottom third of the boat touching the water. With a camshaft producing that kind of torque the engine will not pass smog testing.

Good Luck
Scholman
10-14-2011 10:24 PM
techinspector1
Quote:
Originally Posted by bigalow
Is a marine block any different?
There are certain differences between automotive and marine applications, but I can't see how a sleeve in a marine motor would act differently than a sleeve in an automotive application. Check with a certified marine machinist.
10-14-2011 09:18 PM
bigalow Is a marine block any different?
10-14-2011 07:52 PM
troutman2 X2 on what he said.
10-14-2011 07:13 PM
327NUT It's as good as the machinist doing the work, a properly installed sleeve will work just fine.
10-14-2011 06:44 PM
bigalow
Q's on 454 marine block

A 454 4 bolt main engine out of a boat .030 but dropped a valve and needs one sleeve. Is this any good?
My intention is to build it and put it in my truck

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.