Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Want to rebuild my 10 bolt
User Name
Password
lost password?   |   register now

Thread: Want to rebuild my 10 bolt Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-17-2011 06:18 AM
SSedan64 X2^^^ on the Axles, a good set of Moser, Yukon or Superior etc.. Axles are good insurance.
10-17-2011 05:57 AM
gonefishin' What you may see when you pull the axles is a groove worn into the axle where the brng. rollers ride cause the axle it self acts as the inner race of the brng. If you see thuis you might as well go on and get a good set of axles. I have less fear using the c clip set up if the axles are good ones not stock ones with a groove worn in to them that can be a weak spot. Never mind the new brngs. want a good flat surface to ride on. Replace the seals too but Im sure you know that.
10-17-2011 05:20 AM
SSedan64 Quick Performance has Posi, Gears & Intall Kit Pkg.'s on Evilbay for $535.
http://cgi.ebay.com/ebaymotors/GM-8-...item564695535d
Not sure what brand Install Kits are included, I'd ask for a Yukon Master Install Kit, they have Timken Bearings & Super Shims. Posi looks like a Yukon DuraGrip, not sure about brand of Gears.
10-16-2011 04:50 PM
old west i had a 10 bolt in my truck. it had 3:42 gear non posi. 350 with 425 hp. it hadled it just fine. yeah you could put a posi unit in it. brand new there like $400 to $500. youll need one that will fit a 8.5 ring gear for the 10 bolt. i say the axles would be fine. just make sure the posi unit will have the sme amount of splines as the axles
10-16-2011 03:35 PM
jd71cam
Want to rebuild my 10 bolt

I am thinking about rebuilding my 10 bolt rear end from my 71 camaro. I would like to put a 3:73 gear ratio in. I have a 350 engine, pretty worked, maybe 400 plus horsepower. The cam is a z-cam with a max 6400 rpm range. I have a 2300-2500 stall speed converter and transmission is a strong turbo 350 .. I am pretty sure the rear I have in it is stock and non-posi.(Will check codes on rear) The question I have is, Would I need to replace axles or are the ones I have strong enough. Also, what else should I do to it so it will handle the torque and horsepower? Can I put a posi in it? If I can get away with getting the parts for under 500 hundred, maybe 300, that would be excellent. I dont want to bust my but with this.How long will it take to complete , if I have everything I need? Would like to be prepared and avoid any surprises, Any help is greatly appreciated. God bless

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.