Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 700R4 Corvette Servo question, (pin question)
User Name
lost password?   |   register now

Thread: 700R4 Corvette Servo question, (pin question) Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-10-2011 12:05 AM
SSedan64 Yes, same method & spec, if you have room to check it installed in the Truck.
11-08-2011 03:37 PM
Guntar13 A day late and a dollar short! I put the trans back In today! ( wild hair up my ***!). It is a 91 Chevy truck 2wd, lots of motor mods done so lookin to "sharpen" things up a bit. Thanks for the info, I assume with the trans in the car it's the same rule of thumb as far as clearances go? Thanks!
11-08-2011 03:28 PM
B@D What type of vehicle are we talking about first of all , are you wanting a firmer shift ?

As for the pin most of the time you can get away with using the same pin and some times you have to grind the tip just a little to achieve proper band clearance.
Putting in the vette servo will not change band clearance but changing to an after market 4th servo cover,piston can change band clearance.

1/16 - 1/8 '' is ideal band clearance in most 700r4's , here is how you can check it >>>

Before you remove the original servo cover either mount the trans in a fixture or simply place it against the wall so you can push on the servo cover to see how far it moves inward away from retaining clip because that is your band clearance > that is where you don't want more than 1/8 " , no less than 1/16 " clearance .

After you replace the servo with the ones you choose be sure to check the clearance again , adjust if necessary then .
11-08-2011 11:09 AM
700R4 Corvette Servo question, (pin question)

I am getting ready to mount the tranny back up and before i do i wonder if i should install a corvette servo and 4th apply piston. My real question, being how i have read countless benefits of this, is whether i would need the longer pin? There are very moderately priced kits that have the 2nd servo and new pin, but I wonder if it is really necessary to replace the pin since I will be putting the 4th apply servo on also. Thanks for the info!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 09:12 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.