Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 4.56/3.73 Gears
User Name
Password
lost password?   |   register now

Thread: 4.56/3.73 Gears Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-06-2011 11:38 PM
hellfridge http://www.youtube.com/watch?v=Zgl5xcZmWpI


this might help its on a new f150 but it should be about the same idea?
12-02-2011 07:56 AM
matts37chev but it would be a cheap way to get a set of gears and a 31 spline carrier
there is a chance it will be close and maybe between the two rears, you can put something together without having to buy too many parts
12-01-2011 10:35 PM
SSedan64 Very doubtful, you would still need to check Pinion preload, Gear backlash, and Wear/Mesh pattern when swapping Ring & Pinion and Diff. You could start with the stock Shims & go from there.
12-01-2011 05:04 PM
Mac88 Another question just for learning. So if I pulled a 8.8 rearend with 3L73 gears out of an ford explorer, could the entire assembly be swapped into a Mustang 8.8 without messing with the shims or bearings, just a straight swap? Not the entire axle, just the gear assembly and pinion?
12-01-2011 08:32 AM
matts37chev
Quote:
Originally Posted by Mac88
I realized what I said after I posted that. So, I did'nt cancel the order, and now I have 7.5 in. rearend layingin my garage. More junk for my wife to fuss at me about. Who knows, maybe it will be needed one day.
i have another 7.5 we just pulled out of my kids ranger p-up that you can have for your pile
12-01-2011 03:29 AM
SSedan64 This Link is for a GM 8.875" 12-Bolt Diff rebuild, the Ford 8.8" Diff is basically the same style Rear. It's a very detailed Build so it should help you out.
http://www.webrodder.com/article.php?AID=134&SID=60
One more >> http://www.hotrod.com/techarticles/d...install_guide/

Using a Solid Pinion Spacer would make the Install much easier, you don't have to worry about all the torque required for that Crush Sleeve.
11-30-2011 05:54 PM
Mac88
Re

I realized what I said after I posted that. So, I did'nt cancel the order, and now I have 7.5 in. rearend layingin my garage. More junk for my wife to fuss at me about. Who knows, maybe it will be needed one day.
11-30-2011 05:18 PM
lmsport 7.5 and 8.8 gears dont interchange.
11-30-2011 01:15 PM
Mac88
Re

Just found my own answer. Out of a Ford Ranger, 7.5. Oh well, maybe I can still cancel my order and use the gears. They are 3.73s.
11-30-2011 01:11 PM
Mac88
Re

Friend of mine just showed up about an hour ago saying he had something for me. It was a rearend, eventhough I've already ordered a gear set. But the id tag reads as follows
S390D 373 A75 8E04
Can anyone tell me what this is out of? He knew I was looking for a set of 3.73 gears. But I'm just curious for my learning curve, is this an 8.8 in. rearend and would it have worked in my 88 Mustang 5.0?
11-30-2011 09:59 AM
matts37chev i have been told that this is a good book

thats the best that i can help
i dont know of any web postings
11-30-2011 09:50 AM
Mac88
4.56/3.73 Gears

I posted this a while back, and I got a little feedback. I just wanted to run it by everyone one more time. I have a '88 Mustang with 4.56 gears installed. I bought a set of 3.73s and a install kit to replace the 4.56 gears currently in it. I'm somewhat mechanically inclined, and I just wanted to ask could this be done in a home garage? I dont drive the car everyday, so it's no rush to get it back together. Basically, I use it as a learning tool. And does anyone know if there's a posting anywhere with a step by step walk-thru on how to do it? I've seen a few, but they're not very detailed.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.