Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> Plastic fuel tank repair
User Name
Password
lost password?   |   register now

Thread: Plastic fuel tank repair Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-24-2011 07:38 PM
tnovot Although I have never used it on a gas tank, I have made successful repairs to a variety of plastics with JB Weld. It was recommended to me by a friend who owns a body shop to use the fast set formula athough I have also used the regular with good results.
Terry
12-22-2011 09:02 PM
Bryan59EC Hard to find these things----are not reproduced.
Even the sending units are obsolete now.

But---I did have a major brain fart.
I just took it to the body shop (I spend a lot of time there), after I realized that Hector fixes bumpers all the time.

He had me clean the tank off, get my dremel, and clean out the crack and put a "V" in it.

He then warmed it up and "welded" it closed again.

The crack is (was) at the top on a factory seam, so when I get around to putting it in my truck (hoping existing brackets will work as this tank is larger), I will put some neoprene or some kind of rubber every place the tank comes into contact with the frame.

I probably would have never even noticed the tank was cracked, had I not tipped it on it's side and then saw it start seeping.

Next----on the hunt for a good sending unit.
12-22-2011 08:49 PM
Flipper_1938 Plastic fuel tanks are made out of High Density Poly Etholene (spelling?). Not much will stick to it.

Only chance might be to re-melt the plastic with something like a sodering iron. ...But I don't think you will ever get the crack clean enough to not have contamination in your weld.

I'd find another tank.
12-22-2011 08:36 PM
dogwater Fiberglass patch?Maybe a patch about twice as big of the crack.As long as theirs not flexing where the patch is.Sand area,clean with aectone then Home Depot fiberglass sheet & glue.I've seen duct tape & fiberglass glue used on gas tanks.
12-20-2011 01:07 PM
Bryan59EC
Plastic fuel tank repair

Some time ago, my 82 Dodge D-150 developed a pretty good sized leak.
Cannot fill the tank, or it will be leaking 'till it gets to 3/4.

As most of us know, most salvage yards destroy fuel tanks by poking a big hole in them while they process the car.

Today, I bought a tank from a yard that does not do this, but alas, it has a crack at the top. Not a big one, and most likely would not leak for a day until the fuel level dropped.

Pretty sure this small crack will put me in better shape than the tank currently in the truck.

Anybody here repair small cracks or holes in plastic tanks????
How is it done??
Is there some place I could take it for repair???

This is a larger tank than currently in the truck, not an easy job to pull.
Requires bed removal or rear end removal to get out. (Not really sure if there is enough room to slide it past the trans) I like the idea of a larger tank, but either way I need to get one of these repaired. Old Dodge pickups aren't growing on trees anymore, and I thought I was doing good just finding a decent tank.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.