Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> real gear welder 140 mig
User Name
Password
lost password?   |   register now

Thread: real gear welder 140 mig Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-01-2012 10:27 AM
StreetKruzer I have an old Hobart Handler 135 which they don't make anymore. LUV IT! Still does everything I need up to 3/8" and still 110v. The newer Handler 140, etc. are after Hobart was bought out and windings and such are not as they used to be back then. (This from the welder repair people, they say some other major welder MFG bought them, kept the name, and cheapened the lower end units to compete w/chinese, etc.). If I were buying today, I would look hard at Miller 175 for all around. When I got the Handler 135 I needed something to plug in to 110. Bob
03-01-2012 10:11 AM
jfl1960
Mine works great.

I have a Lincoln Mig Pak 10 (90 amp wire feeder with FCAW and GMAW capability) that has been in my garage since 2001 and still works like a charm, absolutely great for light duty but found it was not hot enough for anything above 3/16 and when welding heavier materials it would shut down due to exceeding duty cycle if I were welding anything long like 6 inches or more at max setting.. I found one of these Real Gear 140 units in a local buy and sell for $250.00, it looked like new and was hardly used, original roll of hardwire was only 1/2 gone, problem was the guy who had wasn't a welder and didn't understand amperage requirement of this unit, it was running it on a 15amp circuit so he thought it was junk as it wouldn't weld very good for him, I tried the machine and found it running very cold but since it wasn't getting enough amperage to start with I took a chance and got it, it actually requires a dedicated min 20 amp 110V circuit to run properly which I have installed in my garage, I am very impressed so far, it is a Lincoln knock off and therefore uses all the Lincoln consumable parts like nozzles and tips, not sure about liners, or whips, I will try and swap my whip from my Lincoln and see if they are compatible. I have gone through 5 10lb rolls of .035 FCAW wire so far and this welder has only shut down once from exceeding the duty cycle, was welding a combination of steels from 1/8 up to 3/8 with no problems and great penetration. This welder came with a gas setup but I use it for FCAW all the time and now leave my Lincoln setup for GMAW all the time. Personally I like it but as stated these units are kinda like the old fords of the 60's and 70's, one is great and the next is a lemon, they are very reasonably priced. Good luck.
01-07-2012 01:17 AM
BigEd36 Poor warranty and Chinese made. I would walk away. For the same $$$ you can buy the Auto Arc 130 which is made by Hobart and carries the same warranty that Hobart welders have. Here's the Auto Arc 130 for $327.21: (notice this one doesn't include the regulator and hose but is a true mig welder, not just flux core) Amazon $406.29 and TSC $399.99 (online only) has the Auto Arc with a regulator, cart and helmet.



The reviews are great for the welder, pretty bad for the cart (mainly screws don't hold well, but.....ya got a welder!) and, especially the cheap helmet, but a decent auto darkening helmet doesn't cost too much. These welders are warranted by, and parts and service are available from Hobart.

The Hobart Handler 140 has a very good reputation and can be bought for $499.99 at TSC. TSC also has the Hobart Handler 125 for $369.99.

In my opinion any of these, as well as others from Miller and Lincoln, would be a much better investment than a welder from China that would be hard, and probably impossible, to get service/parts for.

Ed
01-04-2012 05:18 AM
silentpoet Can't go wrong with a miller, hobart, or lincoln. Not to say that others are worthless, but you take more of a chance.
01-02-2012 04:14 PM
crussell85 There is sure a lot to be desired with the warranty.

Limited 1 year/90 day warranty- One (1) Year, from the date of purchase, that the transformer and rectifiers are free of defects in material and workmanship. Ninety (90) Days, from the date of purchase, that the gun, liner, wire feed mechanism, welding clamps, electrode holder, cables and accessories packaged with the welder are free of defects in material and workmanship. This does not apply to consumable parts, tips, nozzles and welding wire.

You can buy a Hobart from TSC for another fifty bucks or so. It doesn't come with the cart and helmet and all the other crap that makes it seem like a good deal. Plus a lot better of a warranty. I would stay away from this welder.

If a product is good then their not scared to put a good warranty on it.
12-30-2011 07:03 AM
huckster427
real gear welder 140 mig

Does any one have this machine ,is it any good??

Huckster427

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.