Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Desktop Dyno 5
User Name
Password
lost password?   |   register now

Thread: Desktop Dyno 5 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-31-2011 09:44 PM
Chevyjeepster
Guess top dyno

I assume I have at least 8.5:1, the pistons are flat tops and I am using .015 steel head gaskets. I have too ck on the heads. I contacted Crane about the cam because I was looking for something in 210@.050. They said the cam would work great in my combo. And that was good news for me as I bought it new off eBay cam and lifters $60 bucks. As for the ground in 5 degrees advance, it didn't have that on the cam card but I will ck in to it. I just put the long block together but still have the timing cover off. Several bushings came with the gear drive but I installed it straight up. As for the desktop dyno I think it's math is a little fuzzy. Your numbers seem pretty close to what I was thinking but all I was hoping for was a daily driver for my jeep.
Jimmy
12-31-2011 07:31 PM
whyholdback I never got accurate results from any version of DD by using honest inputs. You have to try a lot of known builds to learn how to lie to each version of DD.
That's a way wrong cam for the rest of your combo, and if you installed it dot-to-dot, then remember that it has 5 degrees of advance ground into it. If you installed a cheap timing chain, then the chain will stretch, badly.
If that's the sort of cam you want, then at least mill the heads 0.030" to get the compression up to 8.5:1
Your combo as typed says stock low-performance heads with 1.94 / 1.60" valves. Hate to tell you, but as GM never offered that combo of valve sizes, then the heads aren't stock.
Still, assuming you built this engine this way, you should have maybe 275 HP peaking around 5000 RPM, and maybe 325 ft-lbs around 3500 RPM.
What sorts of results were you hoping for, anyway?
12-31-2011 06:31 PM
Chevyjeepster
Desktop Dyno 5

I bought desktop dyno and a little concerned about the test results. When I plug in all the info it seems to be off somewhat from experience. I ran a 350 chevy 8:1 comp, stock low performance heads 1.94-1.60, dual plane intake, 750 cfm, small tube headers without cats, a Crane 272H10 cam straight up.
I get 262 hp@ 4000 and 396 ft lb@2000. The hp seems to be fairly close but the torque seems to be off about 70 ft lbs or so. I know that it isn't going to be 100 percent but with the weather and alt. Dialed in I thought it would be a lot closer. Has anybody had any luck with this dyno.
Jimmy

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.