Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 502/502 cam upgrade
User Name
Password
lost password?   |   register now

Thread: 502/502 cam upgrade Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-11-2003 06:58 AM
1BAD80 Here are the 2 cams from GM. I would stay with the GM intake its better than the Edelbrock. Get a Good Holly carb for it,
If you can afford it get one with annular booster's for response.

14096209 Hydraulic Flat Tappet "502"
This hydraulic flat tappet "502" is a good street high-performance and marine cam used in the Gen V 502 H.O. engine P/N 10185085. The duration at lash point in degrees (intake/exhaust) is 328/324; duration at .050" tappet lift (intake/exhaust) is 220/220; and maximum lift with 1.7:1 rocker ratio (intake/exhaust) is 500/500.
Valve lash is zero/zero and lobe centerline is 115 degrees.


24502611 Steel Roller
This steel roller is for the 502 and 454 H.O. engines. (Must use distributor gear P/N 10456413.) The duration at .050" tappet lift (intake/exhaust) is 211/230; and maximum lift with 1.7:1 rocker ratio (intake/exhaust) is 510/540.
Valve lash is zero/zero and lobe centerline is 112 degrees.
09-10-2003 10:48 PM
black66
intake

If you are looking for top end power go with a single plain manifold. Like Edelbrock Torker II or Victor JR......... I am running the Torker II on my 530 HP SBC 355. Made a huge difference from the air gap on my setup....... Just my two cents........
09-10-2003 06:50 PM
1BAD80 Here is GM's Performance site it has 2 good Roller cam's for your motor.
http://www.gmgoodwrench.com/gmgoodwr...at=9348žion=ep

09-10-2003 06:14 PM
redcamaro4spd wow, into the 11's, sorry I can't help, but if you get a second, please describe your entire setup. That sounds really kool...
09-10-2003 06:05 PM
malibu502
502/502 cam upgrade

Looking for advice on a camshaft upgrade for the zz502/502 crate motor. Motor is well broken in, runs very strong, but is way under-cammed. Would rather not change valve springs, pushrod length, studs,etc. unless it is really going to be worth the trouble. Was also thinking different intake (RPM air gap?) and carb (speed demon 850 dp?) may match up better with a cam change? Hard to get any kind of advice from GM that seems reliable. Chevelle is in the high 11's, looking to get into the low 11's. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.