Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Best cam for 350 sbc truck engine?
User Name
Password
lost password?   |   register now

Thread: Best cam for 350 sbc truck engine? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-18-2012 06:48 AM
Jimbo17
Cam

You did not explain how much the truck weights and I don't know if you are in the trades and carry tools or anything like that.

I would look for a cam that would increase your low end because that is what most trucks need.

I have an 1986 Chevrolet Van that we put a 350 engine in and the motor was 30 over which makes it a 358ci and with the right Comp Cam it pulls hard and get the van full of tools up to speed fast.

Jimbo
01-18-2012 01:53 AM
DoubleVision What I do know is this thread is 3 years old. I also know thumper cams are fad cams, all bark and no bite. They're designed to make a engine hit a heavy lope exhaust lick and sound good, they aren't so much on power development.
Other high performance cams lope at idle as well as long as the combo is tuned right.
01-17-2012 11:41 PM
84 camaro What do u know about the thumper cams a buddy of mine can't get over how they add so much hp
11-12-2009 05:54 PM
DoubleVision I`d use the Edelbrock performer plus or Summit racing equivilent cam. It`ll work just right for what your looking to do.
11-12-2009 04:21 PM
enduro54 Ok, teh truck is a 91 chevy pickup. the engine details will be:

350 4 bolt main 010 block. Not sure what years these were from. early 70s? or I have a 4 bolt 350 block from a 82 dumptruck either will be bored at least 30 over

stock crank cut .010
Probably stock rods
stock replacement cast flat top pistons
stock 062 vortec heads
Probably stock manifolds from the 91 truck
No smog in my area. Might keep a cat on it so the exhaust does not smell.
700R4 stock trans from the 91.
11-12-2009 03:32 PM
oldbogie
Quote:
Originally Posted by enduro54
Looking for an inexpensive cam that would make good power in a 350 sbc with stock vortec heads, GM perf vortec intake and throttle body. Truck will be used to tow a racecar now and then, I might put a snow plow on it, and will also be used to haul mulch etc. Looking for something that will give pretty good low end torque but doesn't flatten out at 3k rpm.

1) Need to know year of the truck?

2) Year of the engine if it's different from the chassis?

3) Year of the block if it's different from the Vortec heads you reference those being 1996 and newer items for production?

4) Which transmission?

5) Does it need to smog?

There are a lot of changes year to year as to how the systems work and relate. Change difficulty is variable by year, and the cam is usually a large change, especially if when it comes to Manifold Absolute Pressure managed fuel injection. This can get expensive making system and computer chip changes, so it's necessary to have answers to the first questions to even get started.


Bogie
11-12-2009 02:30 PM
enduro54
Best cam for 350 sbc truck engine?

Looking for an inexpensive cam that would make good power in a 350 sbc with stock vortec heads, GM perf vortec intake and throttle body. Truck will be used to tow a racecar now and then, I might put a snow plow on it, and will also be used to haul mulch etc. Looking for something that will give pretty good low end torque but doesn't flatten out at 3k rpm.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:57 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.