Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> 84/16 steelmix gas for MIG
User Name
Password
lost password?   |   register now

Thread: 84/16 steelmix gas for MIG Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-29-2012 08:21 PM
matts37chev i am not expecting miracles, but while im welding these patch panels etc.
i am thinking every little bit would help, me and the thin stuff dont see eye2eye
01-29-2012 08:12 PM
oldred You probably didn't get hurt as long as they didn't charge much extra for it but I doubt it will help with the thin stuff very much. There are all kinds of gas mixes out there, some even have more than two. These tri mixes can even have small amounts of Oxygen which seems to be a contradiction but in certain conditions it can help, usually these exotic gases are for industrial use and the main concerns are speed/production costs more than anything else. Most of them will work just fine for the type of welding you are doing however and unless they charged you a big premium it should not matter much one way or the other. Actually depending on your welder, the wire you're using and surface condition you may very well see a slight improvement, or not, but I wouldn't expect it to be anything to get excited over.

75/25 has been the standard mix for many years and every ratio possible has been tried but the old standard C25 has always been the best for all-around use for a good reason,
01-28-2012 10:55 AM
matts37chev the more Co2 , the deeper the penetration,
(a cheat for using too small of a welder on thick material is use 100% Co2)

so my thinking is...
less Co2 should help to not burn through the thin stuff

or is my thinking off?
I am sure its not that simple, and there is more to it than that
01-28-2012 09:50 AM
S10xGN Never heard of it, I've always used C25 (75/25). Keep us posted!

Russ
01-28-2012 08:52 AM
matts37chev i have been searching the interweb all morning and cant find any real solid info

but with stuff I have found, it still looks good on paper
01-27-2012 07:23 PM
matts37chev
84/16 steelmix gas for MIG

i talked to the guys at airgas about the 84/16 steelmix
they said it would make my life easier on the thin stuff
(compared to the 75/25 that I had been using )
so thats what I got

did I screw up? anyone else use it?
I remember it was mentioned by someone in a thread a while back

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.