Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Paint stripping...
User Name
lost password?   |   register now

Thread: Paint stripping... Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2012 08:35 AM
Javelin69 Say's you can wet sand it with 400-600g or dry sand with 320-400g after it's dried for 8-10hrs.
02-09-2012 06:11 AM
deadbodyman R-Ms is a good brand but I'm not familiar with there epoxy,it should be good as it sandable???
02-07-2012 05:33 PM
Javelin69 I'm using RM's EP569 Epoxy Primer as well as there DP25 Primer Filler...
02-07-2012 04:52 PM
Old Fool skip the wire brush treatment, it burnishes the metal, not what you want.

SPI epoxy will go on the sandblasted panels without further surface prep. Just clean and coat.
02-06-2012 06:23 PM
Javelin69 I'd figure go by hand and get better tooth, with the DA it'd be shinier, would'nt it? But hey, ths DA would go helluva lot faster...
02-06-2012 02:15 PM
deadbodyman Thats what I would do with the exception of the jambs ,there I'd just use the stripper wheel then epoxy,no sanding....same with the back side of doors, trunk, etc
use a DA sander with the 80 not by hand you'll get a MUCH nicer job , faster too
02-06-2012 10:48 AM
Javelin69 ok so, hit it with the stripper wheel, and wire wheels. Then hit it afterwards with 80grit by hand to give it a rough surface, then the epoxy paint hits the metal...
02-06-2012 06:15 AM
deadbodyman yes AND no...when you strip the factory paint off what you'll see is snooth metal with no scratches at all,its always that way so the stripping wheel alone will work and chem strip is the samewith even less molesting of the surface if done well..although I have epoxied over some cars after a good cleaning of the metal and it worked just fine ,most times I will sand with 80 or 180 it just feels rightand if its old steel you should really sand it good and clean it well Ive seen little rust specks and all kinds of stuff under paint..stripping without sanding should really only be done on newer steel...I'd say about no more than 10-12 yrs old ...give or take....
02-05-2012 11:35 PM
Paint stripping...

Hey guys, I was just wondering. I'm using a couple of different paint stripping methods, the 3M purple strip wheel and sandblasting. Will either of these methods give enough tooth to shoot an epoxy primer or afterwards? Or should I hit it with some 80grit on the da sander and hand sand it, after the other methods are done first? Any suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 11:39 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.