Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Body Work
User Name
Password
lost password?   |   register now

Thread: Body Work Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2012 06:29 AM
deadbodyman
Quote:
Originally Posted by Formulajim
Be careful with that e-coat try to take it off with lacquer thinner if it doesn,t wash off its ok but if it washes you need to get it all off. The tiywon stuff is bad news. I would put new skins on the doors it's way better looking in the end and easy to do. Epoxy first not cheap nightmare paint. Then filler,2-k high build primer, block it out use guide coat. If its high you hit metal if it's low it shows up guide coat.
so true ..If your going to spend any time at all working an after market panel the first thing you do is remove all that junk primerwether it washes of or not just sand it off an start with an epoxy that you know is good ...the whole job is relying on that primer why would you take a chance on something your not sure of ??
02-19-2012 11:53 PM
icecube508
bodywork

It depends on the type of epoxy you use. If its dtm the its only useable only on cleans substates. ie: properly cleaned steel, frp, rigid pp and alluminum. Its because of the solvents that in its composition. Non - dtm epoxy can be sprayed over properly prepped clearcoat, basecoat, primer and e-coat with no degragation in the primer. As far as body work. those doors can be fixed but not worth the time to do it. the metal is already stretched and will require a large amount of heating pulling and shrinking to get it to the point of using a filler, thats if you want to spend the 40+ hours to work the metal .. Imo i'd replace them. The rest is workable and dont look to bad. I'd spray a 1 coat of dtm on the bare metal to keep it from flash rust since you still put filler over top of it. keep up the good work
02-19-2012 11:07 PM
tech69 do it to the best of your ability and know filler will fill the lows but can't fill the highs. You can mound the highs but you can't fill it. So basically, it's most important to do almost perfect metalwork for your high. My only highs are really subtle and on edges where it won't be noticed.
02-19-2012 10:28 PM
Formulajim Be careful with that e-coat try to take it off with lacquer thinner if it doesn,t wash off its ok but if it washes you need to get it all off. The tiywon stuff is bad news. I would put new skins on the doors it's way better looking in the end and easy to do. Epoxy first not cheap nightmare paint. Then filler,2-k high build primer, block it out use guide coat. If its high you hit metal if it's low it shows up guide coat.
02-13-2012 06:03 AM
NOVA1958 The body is not in epoxy yet just ecoat on the quarters and factory paint in the other places.The trunk and door have 2 coats of ppg shopline epoxy on them now and I'm planing on putting other coat on the door and trunk before I start the filler work.
Here's some pics of the dr side fender I'm going to have to purchase a passager side fender its to far gone.
Thanks for the replies.



02-13-2012 05:53 AM
deadbodyman
Quote:
Originally Posted by OneMoreTime
Just do the metal work as good as your skills allow..It gets better with practice is all I can say.. Looking good from here..


Sam
Although there are metal workers that can straighten metal so close they dont need filler...I'm not one of them so ther will be a point where you just cant get it any better and your just wasting time..You'll know when you get there,then get the filler out...
It looks pretty darn good to me too,I've seen pro's do worse...IMHO your ready for filler .....well ,a good cleaning with W&G, epoxy THEN filler
02-13-2012 12:55 AM
dinger If the epoxy you are speaking of is epoxy primer, you really should use it for your base. It won't do as well when sprayed over primer. I am sure one of our experts will correct me if I am wrong, but I believe it is epoxy primer on the bare metal, bondo and other primers can be sprayed over the epoxy but you need to seal the metal with the epoxy.
02-12-2012 06:22 PM
speedydeedy It is best to get it as straight as possible but it looks good to me. I would start filling then priming.The main thing is you don't have swiss cheese rust holes. Everything I see is good solid metal just dents so you are good to go.
02-12-2012 06:08 PM
OneMoreTime Just do the metal work as good as your skills allow..It gets better with practice is all I can say.. Looking good from here..


Sam
02-12-2012 05:56 PM
skip99 you might be better off putting a skin on the door, quicker and easier... as far as the quarters, how you gonna get the cheap stuff out of the low spots?
other than that, bondo and epoxy or epoxy and bondo..looks close enough..
consider spraying feather fill...it'll save you time..

I did the same thing to this one,, quarters, and door skin
02-12-2012 05:19 PM
NOVA1958
Body Work

Hi everyone
I'm in the being stage of doing the body work on what 72 Nova and need to know if everybody tries to get ever high and low spot out before they add filler or do you get it close and start filling.On the body,to save on epoxy paint I've been working the metal before I epoxy then I'll mist with cheap spray paint then block sand work metal again and check metal again.When finished I'm planning on sanding all the cheap paint off and when spraying with SPI epoxy.Both quarters were replaced with half quarters and I flanged the car and I mig welded the quarters.The door was pretty meshed up and took alot of work to get it looking this good it had alot of filler on when I first sanded it down.Please all body guys chime in.






Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.