Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Burned out my new starter! Why?
User Name
Password
lost password?   |   register now

Thread: Burned out my new starter! Why? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-09-2002 08:34 AM
Dave E Shank MARTZY: A good sugestion would be to install a battery disconnect switch. The little switch with a turn knob on top are less than five dollars at a swap meet. To tell if you need shims they say to use a paper clip between the starter drive gear and flex plate. You can use a srew driver to pull the starter bendix out which will push the starter gear out onto the flexplate. That is where you make your clearance measurement. If the starter motor stayed engaged electrically then you had a short in the solenoid circuit. You should be able to check that with a light or voltmeter to see if there is 12 volts on coil side of solenoid when you turn key to start, it should drop off when you go to run position. If that checks out okay then do voltage check on power side of solenoid and see if there is 12 volts on power terminals when there is no power on coil. For the starter to stay engerized all the time there has to be a short in the solenoid as it is the only thing in the circuit between battery and starter ground. You know years ago when they had cranks you never would of had this problem. Let us know what you found. GOOD LUCK DAVE E SHANK
07-09-2002 08:11 AM
Martyz7
Burned out my new starter! Why?

Replaced a starter for a 305 GM engine, Manual transmission, used no shims.
When I put in the clutch & turned the key, the starter started cranking, when I turned the key to the run position, and then to off, and released the clutch, the starter just kept cranking. As the battery was running down, I tried to disconnect the terminals, but, too late the starter stopped, and burned out a spot on the armature.

What happened?
1. Short in the wiring?
2. No shims caused the starter drive gear to bind into the flywheel gear and kept the solenoid engaged?
3. Any other ideas?

What is best way to tell what shims are needed, on a setup in the car already?

I have heard that you need a paper clip to fit in the valley between the gears on the drive and the flywheel.... How do you see in there? What has to be removed?

Martyz7

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.