Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 86 c10 gearing
User Name
Password
lost password?   |   register now

Thread: 86 c10 gearing Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-01-2012 11:07 AM
kuta1972 i running 325/60r/15 bfgoodrich..finding them hard to come by now so i'll be going 275 or 295 wide my next set...running 40 series flowmaster muffler with no carpet so would need ear muffs with 4.11s lol...mite go high 3s by the sounds of you guys reply...any gains in messing with the converter and putting in a higher stall..i'm getting mixed replys from people some say that the stock convertor is bogging down the truck and some say not to bother if it a mild build..thanks for replys
03-01-2012 04:51 AM
75gmck25 My '75 GMC has a TH350, 4.11 gears and stock height 31" tires (245/75R16). When I drove it to work this week I was running about 2700 rpm at 60 mph. This is not hard on an SBC 350 engine, but it gets fairly noisy in an old truck with very minimal sound insulation. I also have an old chain-driven transfer case generating noise right under my seat, so your 2WD truck should be a little quieter.

I'm going to replace the stock hood insulation blanket (mine fell apart) and also add insulation (dynamat, etc.) to the back wall of the truck behind the seat and to the inside of the doors to see if it helps. I already have full carpet with jute backing, but there is still a lot of bare metal in these old trucks.

Bottom line answer - 4.10 gears work fine and the rpm won't hurt the engine, but the higher rpm makes more noise and the truck sounds like its working a lot harder. This noise increase makes some folks uncomfortable if they are used to modern cars where you can cruise at 60 without any obvious engine noise.

Bruce
03-01-2012 01:03 AM
American Muscle I have 86 C10 with 3:42 gears and a 700r4 tranny with 255/70/15 tires(29in tall). She pures on the interstate at around 2000rpm at 70. And can burn the tires through second with a mousey 305sbc. Was thinking of going 373 or 410 but thats too much tire peeling fun for me.
02-29-2012 11:18 PM
SSedan64 There are several rpm/speed calculators online.
Input a few Rear ratios, Tire sizes etc.. to see what the rpms will be.
Here's a few:
2nd down >> http://hotrodworks.net/hotrodmath/quarter.html
http://www.f-body.org/gears/
http://www.richmondgear.com/01calculators.html

I wouldn't go highwer than 3.73 if you plan on crusing the road. 3.42, 3.55 are good all around ratios.
02-28-2012 11:09 PM
kuta1972
86 c10 gearing

hi all,i wont to change my diff gearing on my 86 c10 shortbox..gearing is standed at the moment and has no take off power at all..dont really care about highway revs but then again dont wont truck to be ringing out at 60mph...alittle lost in what rearing would suit...trucks running a 355 chev with fuelie heads and tow cam..box is a shaft kitted 350 with standed converter..i think its standed anyway..it is blue but can't find any info on it.was going to go 4.11 but was told on the open road she be reving hard out.keen to find out if there any truck owners on hear that have 4.11 gearing and how it runs..cheers all

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.