Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> T-400 question
User Name
lost password?   |   register now

Thread: T-400 question Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-02-2012 05:50 AM
bbowerman is it very possible that my torque converter clutches are bad

oh and rick I was checking out your journal for the 32 ford with chevy engine.
03-01-2012 07:13 AM
rick 427 If you have a dual converter bolt pattern flexplate,you can substitute the 13'' 400 converter with a 350 12''....that'll give you a few hundred rpm's of stall over the 400 converter.
02-29-2012 10:05 PM
bbowerman Also just an opinion it has a cam and is bored over .030 would you go with a stall or not I'm gonna say no because the cam is only slightly bigger than an rv cam. just wondering what your opinion on stall converters are.
02-29-2012 09:52 PM
bbowerman Im gonna finish pulling out the TH350 tommorow so I need one pretty soon I think the TH400 will bolt right in if not I got a Dewalt and some drill bits lol
02-29-2012 09:34 PM
bbowerman or this
02-29-2012 09:29 PM
bbowerman also is this:

long enough or do I need to find a longer one?
02-29-2012 09:27 PM
bbowerman y'all dont happen to know what u joint my 76 half ton would have stock do ya?
02-29-2012 09:26 PM
bbowerman thanks for the advice and info will check it out
02-29-2012 01:26 PM
seven1nova you can try here
02-29-2012 11:43 AM
junior stocker I got tired of replacing the TH350 transmissions in my 82 Silverado, and decided after the last TH350 went, it was time for a TH400. Best move I have ever made! Solid shifts, no lag, and I don't thyink I'll wear it out like the TH350's. Now, the "short" length TH400 is actually shorter than the 9" extension housing TH350 transmissions used in most trucks. I did'nt want to swap driveshafts, or have one made; so, I got a "longer" slip yoke to make up for the driveshaft being just a bit short. This yoke can be cut down as needed, but I did'nt do this. I should have as it bottomed out on the speedometer gear in the trans and shifted it's placement. I don't have a speedometer that currently works due to that, but when the weather finally gets decent again I'll shorten the yoke and reset the speedometer gear. I don't remember the part number for the slip yoke; I got it off of E-Bay. One of it's applications was for use with a transfer case, that may help your search.
02-29-2012 06:10 AM
T-400 question

I am swapping my 76 silverado's th350 with a th400 because the th350 is blown I am going to need a yoke but Im not sure where to get it there are some on ebay I was wondering if someone could guide me too finding this. All help appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:00 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.