Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Edelbrock Calibration Kit - will it work on an old Carter?
User Name
Password
lost password?   |   register now

Thread: Edelbrock Calibration Kit - will it work on an old Carter? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-02-2012 04:49 PM
tjet The return springs that came with the Edelbrock progressive linkage were garbage. They were different dia and length. They also had a short heavy pull.

I found some s/s 4" ultra-precision springs from Mcmaster Carr. The spring tension is lighter than the ones from the edelbrock kit and have a better feel. Mcmaster also has the spring pulls

http://www.mcmaster.com/#catalog/118/1217/=ghrx5y

I'm going to order the Inovative LM-2 wideband kit to tune these carbs.
03-02-2012 04:40 PM
F-BIRD'88 Cool.... A afr gauge/meter will help you get it all dialed in.
Even a simple low cost (heated) narrow band gauge/o2 sensor system is very informative.

Post your results here, when you get it all done.
Lots of people here, can benefit from your information on tuning your dual quads.
03-02-2012 04:34 PM
RWENUTS Carb returns are trick!! Match the rest of the linkage. Nice thing about afb's is you can reach in and adjust the mixture screws from the side using a couple fingers.
Nice looking truck too!!
I built one once but it was a 59 GMC. Long gone now but still tearing up the asphalt in northern BC with a blown 496 BBC.
03-02-2012 04:00 PM
tjet Hey thanks. I'm going to order the kit that's the same for the current Edelbrock 500 cfm [1404]

My primary carb is in the rear. Aparently, the carbs I have were made to run together. The rear carb [4758] has a choke and the normal vac ports. The front carb [4761] does not have a choke or any vac ports.

I'm currently building the fuel lines for it now. I'm going to use AGS NiCopp 3/8 line plumbed into a Canton Racing fuel filter [pic above]. I'm going to braze 2 edelbrock banjo fittings to the Nicopp line [limited clearance - see pic]

I just got my progressive linkage sorted out. Check out my return springs and mounts. I installed 2 s/s studs with spring pulls from McMaster-Carr

http://59chevypickup.webs.com/apps/p...toid=144254782
03-02-2012 01:09 PM
F-BIRD'88 The short answer is yes. The edelbrock parts will fit.

some carter carbs had vry precise 3 step and 4 step metering rods. where edelbrocks are more basic with just a 2 step rod.

the fuel circuit calibrations are not exactly the same between the two brands.
some other minor differences, but go for it.
I believe you can still by carter strip kits too.

tech info , service and carb parts
http://thecarburetorshop.com/
03-02-2012 12:32 PM
RWENUTS Best to go with one that's the same size. That's the advantage you have now. When I built my carbs I used a pair of old Carter strip-kits which covered all of them. I started with a box of old carbs and matched venturis and jets and rods and made a pair that would work. I'm sure your carbs come complete already.
Mine worked good. Hauled the mail and still pulled down good mileage. I built my own linkage to hook them together and set up the front carb as my primary and the back carb as my secondary that opened after the front was about 2/3 rd's open. Even built my own air cleaners. Big oval one and also 2 smaller oval ones that I turned sideways. Used aluminum flat sheets. Lots of fun.
Only problem I had was fuel pressure set up and float levels as I lived at 3500 feet above sea level.
Good luck with yours.
03-02-2012 11:57 AM
tjet Cool.

Is there any particulair kit I need to get? They have a few different ones.

I'm guessing my 500 cfm Carter AFB's would be similar to the Edelbrock Performer 1404, which is also a 500 cfm carb & manual choke
03-02-2012 07:55 AM
RWENUTS Of course you can. I did the same years ago when I put together a dual quad for my sbc.
03-02-2012 07:07 AM
tjet
Edelbrock Calibration Kit - will it work on an old Carter?

I've got a pair of 500 cfm Competition Series Carters, p/n's 4758 and 4761.
They are going on my dual quad 455 Olds.

Can I use an Edelbrock tuning/calibration kit for these carbs? If not, why and what are the differences?

http://www.summitracing.com/parts/EDL-1479/

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.