Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> How much hp will I have
User Name
Password
lost password?   |   register now

Thread: How much hp will I have Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-07-2012 11:24 AM
techinspector1 That ES1014R camshaft closes the intake at 19 degrees ABDC and will result in a dynamic compression ratio of 9.54:1 if you truly do have a static compression ratio of 10.10:1. You'll have to run it on race gas or alcohol to keep it from detonating.

I'm going to list two cams, although there are dozens that would work for you.

Isky 270/280 MEGA Hydraulic, part no. 201271/281-12. Good all-around performance, GOOD IDLE and vacuum. 3.70-4.11 rear axle ratio advised. 9.50-10.50 static compression ratio advised. Computer compatible with stage 1 or stage 2 chip. Stock converter. 2200-6500 effective rpm range. 0.465"/0.485" valve lift, 221/232 duration @0.050". 112 lobe separation angle.

Isky 270 MEGA hydraulic, part no. 201271. Excellent mid-range performance. FAIR IDLE, stock converter. 9.00-10.50 static compression ratio advised. 3.70-4.11 rear axle ratio advised. Up to 650 CFM carb. 2000-6200 effective rpm range. 0.465"/0.465" valve lift, 221/221 duration @0.050". 108 lobe separation angle.
03-07-2012 07:27 AM
TDMoss Would a bigger cam with more lift give me more hp
03-07-2012 07:22 AM
RunswScissors sounds likeyou have a 275-280 HP combo..
03-07-2012 07:19 AM
TDMoss Its a older flat tappet block
03-07-2012 06:59 AM
RunswScissors Is your block a roller cam block, or a flat tappet block? Just making sure your Vortec heads are on an older flat tappet block, or that you're not running a flat tappet cam with roller lifters.

204/214 is relatively tame, but those heads are nice flowing factory heads. I'd put the power in the 285-295 range. FWIW, stock LT1's ran similar lift with less exhaust duration and made 275-300 (F and Y car), but on roller cams.

If you want a good street motor, I wouldn't go much over the low 220's duration. As noted before, watch your valve lift with Vortec heads. You can go larger on lift if you put LS beehive springs with the right retainers and locks. It's a $150 mod that will get you up to 0.525-0.550" lift safely.
03-06-2012 09:38 PM
southshore30 Watch out for those Vortec heads if you go any higher lift! Make sure you have your machinist check retainer to seal clearance if you go with a bigger cam. I have a similar setup but am using the Comp xe4262x 4X4 cam. Just finished putting it together and have not run it yet. You may want a slightly larger carb too if you go with a bigger cam. Not saying mine is the perfect setup. I have the 906 Vortecs, flat tops w/4 valve reliefs so its 9.7:1 per my machinist with the gasket I used and am running a mechanical secondary 650 Holley. 300+ HP expected
03-06-2012 05:59 PM
eloc431962 Camshaft - HP ES1014R [350/5.7L, OHV V-8 Chev. 4]


'67-86 Chevy 5.7L/350 camshaft, Stage 1 high performance. May not be computer compatible. Use hydraulic flat followers. .050" Duration-204/214; Cam Lift-.280/.295; Lobe Center-107/117. Use high performance spring kit p/n VSA3 or ERV943 springs. 1.700" installed height. Coil bind


Here's one from summit. http://www.summitracing.com/parts/SUM-K1102/



Cole
03-06-2012 05:43 PM
TDMoss The cam part number is Es1014r
03-06-2012 08:46 AM
techinspector1 The cam looks way too small for the static compression ratio. Post cam mfg and part number.
03-05-2012 08:43 PM
TDMoss I have 3.73 gears in my rear end
03-05-2012 08:18 PM
lg1969 You could, but you go to big, sure. You get big horsepower but at a cost of lousy low end throttle response drive ability issues. Before you know it, you will need big rear end gears. Etc, Etc $$$$$$$$$$
03-05-2012 05:30 PM
TDMoss If I go with a bigger cam will tht give me more hp
03-04-2012 05:42 PM
DoubleVision I think you mean Vortec heads 12558062 as there aren't any 12558060 heads.
With the small cam you have likely around 275 horses and 340 ft lbs of torque
03-04-2012 05:07 PM
TDMoss
How much hp will I have

350 4 bolt main with 12558060 Vortec heads, Holley 600 carb, headers, flowmaster exhaust, flat top pistons, Compression 10.1.1, rv cam specs
__________INT.__EXH.
.050 Dur___204___214
SAE Dur____276___288
Val lift_____420___443

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.