Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> roughing up clearcoat??
User Name
Password
lost password?   |   register now

Thread: roughing up clearcoat?? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-12-2012 04:04 AM
wayneooo take it into a back alley tell it whos' the boss then rought it up a bit using a weapon of your choice
03-11-2012 11:31 AM
mitmaks Use sanding paste with gray scotch brite
03-10-2012 05:54 PM
gto_ron
one more question

I'm following all your valuable advice, thanks !

I've always used Glasurit clear and had good results with this car and previous jobs. I'd like to try SPI Universal clear also. This decklid might be a great place to try it. Is there such a thing as CC mismatch? Should I stick with the same CC all over and play it safe?

regards

Ron
03-10-2012 03:32 PM
rainbow lungs Wet sand the entire piece with 800.
Do your spot repair. At least three coats of base.
Each coat of base go out 2-3 inches.
First coat 2-3 inches past where you see your sealer.
Next coat 2-3 past the fresh base and the last coat 2-3 past that.
Re-Clear the entire lid 3 coats.
Wet sand 1000 grit by hand with sponge pad. This get any dirt and orange peel if any in clear.
Then DA wet sand with 2000,3000, 4000 grit, this makes it almost shine
Now polish.

Lungs
03-09-2012 11:14 AM
deadbodyman 12345678910
03-09-2012 09:25 AM
tech69 blending is easy and plus you have to worry about fresh solvents in your base reacting, unless you seal.
03-08-2012 08:00 AM
gto_ron Thanks to all!

I intend to reshoot both BCand CC over the entire decklid 'cause I'm not a good enough painter to blend it like the pros. I will use all your info and appreciate it.

DBMan, the quarters actually came out OK after some advice from the Forum and the car looks good but this decklid thing is pissing me off. Warm weather is almost here and my car is not ready.

regards

Ron
03-08-2012 06:33 AM
deadbodyman Hey Ron ,I remember this car ,You put 1/4s on and had a fitting problem with the decklid ...first off you dont want to use a sealer...if your DA sanding use 320-400 and if wet sanding 400 to sand the area you want color on if your doing a blend,and 600-800 on the rest thats to be cleared but blending is a little tough for someone without experiance and if I remember correctly your car is black so you can base the whole deck and not worry about blending ,it'll still match....one of the few advantages of using black any other color would need blending....
03-08-2012 06:00 AM
jcclark You'll get a much "straighter" finish if you sand the existing
clear with 600 or coarser.
03-07-2012 09:20 PM
tech69 I'd use 1000 for the clear area careful to not burn thru to the base, which may want to react since it's fresh. I'd also mist that base on there for the same reason.
03-07-2012 08:16 PM
TucsonJay I use 600-800, or red scotchbrites.
03-07-2012 07:47 PM
gto_ron
roughing up clearcoat??

After repairing a small corner dent on my decklid I've sanded through the BC/CC and the epoxy primer sealer I used is showing. The rest of the decklid BC/CC is solid but I have to reshoot the entire piece to avoid the CC repair 'edge'. Do I need to rough up the rest of the CC surface before I seal it? If so what is recommended? Scotchbrite? 800 grit wet or dry?

thanks for any advice

Ron

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.