Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> tips for installing air gap intake
User Name
Password
lost password?   |   register now

Thread: tips for installing air gap intake Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-01-2012 07:55 AM
75gmck25 Edelbrock recommends their gaskets or an equivalent Fel-Pro, and I've used both without any problem. The key is that these recommended gaskets are soft enough to seal the aluminum manifold to the iron heads. Some gaskets are too inflexible and they will not provide a good seal.

The use of RTV instead of rubber seals on the ends is recommended by just about all the manifold manufacturers. You are just trying to keep the oil from leaking, and there is no real pressure to seal against.

Also make sure you use RTV to seal the inner bolts on the manifold. The threaded holes go through and into the lifter gallery and oil will wick up the bolts and onto the manifold if the threads don't have RTV. It does not hurt anything, but you will have little trails of oil on your brand new manifold.

Bruce
03-31-2012 02:59 PM
Richiehd
Quote:
Originally Posted by yardman
why is that
That Air Gap has no crossover for heating the carb. You up north guys will have to drive all day to get the cold stumble out of that motor.
03-31-2012 10:07 AM
matts37chev
Quote:
Originally Posted by yardman
hi need some advice with installing the air gap from elderblock #7516 i bought the fel pro gasket but its not perfect lineup. and i have to use ATV on the ends of the block.i can tell i will have a leak for sure. is there any advice or a better gasket. maby the elderblock not fel pro...........383 chevy stroker
how about a pic of this mis-alignment ?
lets see how bad it is
03-31-2012 09:57 AM
DoubleVision Why pay edelbrocks price when the gaskets I suggested will work and be cheaper?
03-31-2012 07:42 AM
delawarebill
RTV on gasket

u can use rtv on the water jacket areas.. but keep it real thin. its generally not used in that area, but if u keep it to a min u should have no problems..
03-31-2012 07:34 AM
yardman yes i know to use atv on the ends do you put any around water ports or not. thanks
03-31-2012 07:29 AM
delawarebill
gasket ??

when u say "ends of the block" ???? are u talking about the front and rear areas that use the smaller rubber gaskets???? if so i think most will advise u use "RTV" instead of the gaskets.. put a good bead and put intake on while its still wet. I use the hi temp RTV with no problems...
03-31-2012 06:03 AM
yardman well i think that is what i will do. i thought fel pro would be better..as they are on some application's. but with the advise from someone here i went with the fel pro. i will order today elder block and the stuff that helps stick them in place. thanks
03-30-2012 08:40 PM
unix
Quote:
Originally Posted by yardman
hi need some advice with installing the air gap from elderblock #7516 i bought the fel pro gasket but its not perfect lineup. and i have to use ATV on the ends of the block.i can tell i will have a leak for sure. is there any advice or a better gasket. maby the elderblock not fel pro...........383 chevy stroker

The manifold says in the instructions to use their gasket set, think I'd do that. I try and stay with matching the hardware and the install items, seems like a logical choice, mix and match is possible. Then the question becomes how many times do you wish to do the same install? You already have one under your belt and the post sounds like it is not working out as you thought. So with that in mind why play around RTP "Read The Poop" and follow the poops instructions, remember they are the R&D of that product.
03-30-2012 05:42 PM
yardman why is that
03-30-2012 05:39 PM
BOBCRMAN@aol.com And don't plan on using the car on days colder than 45 degrees..
03-30-2012 03:24 PM
DoubleVision I think you mean E d e l brock. Go to the parts store and get the cheapy Mr. Gasket intake jobs that are hanging on the shelf.
03-30-2012 02:22 PM
yardman
tips for installing air gap intake

hi need some advice with installing the air gap from elderblock #7516 i bought the fel pro gasket but its not perfect lineup. and i have to use ATV on the ends of the block.i can tell i will have a leak for sure. is there any advice or a better gasket. maby the elderblock not fel pro...........383 chevy stroker

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.