Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Installing a carpet kit.
User Name
Password
lost password?   |   register now

Thread: Installing a carpet kit. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-07-2012 11:20 PM
MARTINSR It's not a four speed. The entire shifter, boot and linkage would have had to have been removed and I just didn't feel like doing that if it wasn't needed. And it wasn't being the console covered up any hole I cut even if I had screwed up royally.

Brian
04-06-2012 07:15 PM
fourspeedwagon You're probably long done with this (then again, you said you've had the carpet for 15 years so?) but, wouldn't you need to remove the shifter boot anyway? Then it'd be easy, pull the shifter and feel exactly where to cut.
fourspeed
04-04-2012 07:01 AM
DanTwoLakes Way to go Brian! I'm glad I could help. How about some pictures?
04-03-2012 11:06 PM
MARTINSR Thank you so much Dan, I got it all in and your advice really helped me out! It took a lot of nervousness I would have had out of it.

Thanks agian

Brian
03-22-2012 02:49 PM
MARTINSR Thanks so much Dan, what a difference a little "demysifying" the subject does.

Brian
03-22-2012 09:33 AM
DanTwoLakes Brian: You can also cut a long slice, fit the carpet, and then use carpet tape to close up any excess cuts.
03-22-2012 07:53 AM
MARTINSR "Cut a clean hole" that is exactly the kind of expert advice I needed. I was thinking one wrong cut and I have to throw it away. Thinking more like a pro, make a clean cut and you can repair your mistake is EXACTLY what I needed, thanks Dan.

I woke up this morning early thinking about this (don't you just love that) and I remembered about how large the console is and how the shifter is a foot or more from the front of it, so I can make one heck of a screw up and still will be fine. I'll be out there tonight starting my project.

Thanks again!

Brian
03-22-2012 07:13 AM
DanTwoLakes There wouldn't be any holes in the carpet because there are cars that are the same as yours but have shifters on the column that wouldn't require a hole.
About the only thing you can do is remove the knob from the shifter, measure as accurately as possible, and cut the absolute smallest hole you can cut to get it over the shifter. You can always expand the hole after that. Cut a clean hole so you can replace it if you make a mistake. Get some carpet tape from a carpet installer to do any patching from the back side.
03-21-2012 10:04 PM
MARTINSR That's what I was thinking, done that before. But this time, the big hang up for me is that darn shifter sticking up. I am entertaining the thought of removing it. But it's kind of a pain with an old rubber boot that is very odd and not available repro. I hate to remove it and mess up that boot.

But that's my problem, cutting that first hole to slip it over the shifter.


Brian
03-21-2012 09:47 PM
NEW INTERIORS I use a ice pick..
03-21-2012 09:27 PM
MARTINSR
Installing a carpet kit.

Ok, I just grabbed my carpet to throw in the Gran Sport and it doesn't have a single hole. I thought it would at least have the shifter (don't know why, just assumed) and there it is, nothing.

It's a formed carpet with a heal pad built in bought from one of the muscle car repro places Year one or someone like that. I have had it for about 15 years so I don't remember.

Anyway Dan, any quick tips on finding how to cut the hole without ruining it? How about the other holes, seats, seat belts, any ideas for me?

Brian

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:02 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.