Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> no rear brakes
User Name
Password
lost password?   |   register now

Thread: no rear brakes Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-12-2012 10:41 AM
John long Spokes101 is copying and pasting entries to threads all over the forum. None of them have anything to do with the subject at hand. Just ignore that post.
04-12-2012 08:49 AM
S10xGN Now I'm confused, who exactly has the problem? "rreistino" was the original poster, but some guy called "spokes101" pipes up saying "it still want bleed off". So do we have two peeps working on the same car or is this one guy with two handles? And neither poster has stated what they've actually tried doing so far...

Russ
04-11-2012 07:20 PM
milner just a question, did you just put the manual master cyl on. i assume the car was originally power brakes, if so , did you change the push rod. best way to check push rod adjustment, with master cyl empty, look down into the ports, if they are blocked off, the rod is out of adjustment. you should also take the lines off the master, when you get it bleeding properly there, then it should be good at the back. just saves alot of trips back and forth. keep us posted.
04-10-2012 07:08 PM
spokes101 it still want bleed off any help would be great
04-09-2012 08:43 PM
John long Go to. http://www.classicperform.com/TechBo...t.htm#testprop

See section "Test combination/proportioning valve"
04-09-2012 08:28 PM
milner the only reason the valve trips, is to turn on the brake light on the dash. it does not shut off fluid. you will find when you blow a brake line, and you pump it enough, one side or the other of the master will go dry, depending on what line blew [ front or back ]. this is why they use double master cyls, so you still have some brakes. single cyls were outlawed, because when you blew a line, you had no brakes at all. not trying to be a smart ***, this is just the way it works.
04-09-2012 08:04 PM
John long As I understand it the valve is designed with a check valve that will travel to the end of the passage and block off the line in case of a broken brake line or blown wheel cylinder. Sometimes it will stick and until it is recentered no fluid will flow to that part of the brake system. Hence you will get no fluid flow even with brake line loosened.
04-09-2012 07:56 PM
milner you do not need to center the valve to bleed brakes, it only needs centered for proper pressure, which it will do its self when it is bled out properly.
04-09-2012 07:19 PM
John long If you unhooked lines and still won't bleed Brian has given you the correct advice. Proportioning valve probably needs to be centered.
04-09-2012 07:12 PM
milner you have to back off the adjuster to get the drum off. when you do you, you will find the wheel cyl seized. if both wheels are tight, it will be a rear break hose. good luck.
04-08-2012 11:08 PM
MJS69
Quote:
Originally Posted by MARTINSR
Sounds like the proportioning valve to me.
Agreed....with front disk and rear drums, you probably have a combination valve....it needs to be recentered before it will bleed. Once you get it recentered, you will have to hold the pin on the passengers side of the valve in, or use a combination valve center stop that screws into the top of the valve where the brake warning light relay attaches....
04-06-2012 01:42 PM
MARTINSR Sounds like the proportioning valve to me.

Brian

04-06-2012 12:13 PM
kleen56 A couple of things... Is the MC from the corvette for drum or disc brakes? It makes a difference. If your running drum brakes in the rear and disc up front, you need the same for a MC because there is a big difference in brake pressure between drum and disc brakes. Secondly, try a mallet and hit the drum on the sides, not so hard that you break the drum but enough to dislodge whatever is frozen.
04-06-2012 08:49 AM
S10xGN
Quote:
Originally Posted by rreistino
ok heres my setup 78 camaro drag car manuel brake swap with a ford 9in rear end I used a 72 corvett manuel MC when trying to bleed rear brakes pedal gets hard but I get just a drop or two of fluid out of the bleeder now i cant get one of the rear drums off I unhooked all lines to that brake and it still want bleed off any help would be great
You may have to back off (unscrew) the manual adjusters to get the drums off.

Russ
04-05-2012 11:07 AM
rreistino
no rear brakes

ok heres my setup 78 camaro drag car manuel brake swap with a ford 9in rear end I used a 72 corvett manuel MC when trying to bleed rear brakes pedal gets hard but I get just a drop or two of fluid out of the bleeder now i cant get one of the rear drums off I unhooked all lines to that brake and it still want bleed off any help would be great

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.