Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> I need a carb spacer
User Name
Password
lost password?   |   register now

Thread: I need a carb spacer Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-13-2012 08:09 PM
1971BB427 You could have saved some fittings by simply pulling that plug and grinding off the excess height that sticks up. It would still have plenty to hold the allen and tighten.
04-13-2012 01:47 PM
sc2dave while you're at it, you can do this, http://community-2.webtv.net/mattgru/carb/
04-02-2012 01:21 PM
Ekki Hi guys,

and first of all thanks for your suggestions.

I thought about tapping and I also thought about a carb spacer but finally a friend of mine (who knows a plumber...) offered his help.
He fabricated this -



It works!
03-06-2012 09:20 PM
southshore30 I had the same problem but with the manifold vacuum port behind the carb and had to use a spacer. I think someone else mentioned your best option, tap that plug a little deeper. What is it, maybe 1/2" pipe thread? Coat the tap with grease to collect the shavings and push it a little deeper and you may be good
03-06-2012 08:09 PM
Jake_Dragon Can you remove the carb and install the fuel line then bolt the carb back down?
Looks tight but you may have enough room.

But a 1/2 spacer wont hurt the carb, Jegs and Summit have a large selection.
I have aluminum spacers on my car and they work great, I sealed the bottom to the intake and just use a paper gasket between the carb and the spacer.
03-06-2012 07:10 PM
sqzbox Can you use a flexable line to the primary to raise the connection?
03-06-2012 05:45 PM
V305 Maybe you can tap the hole so the thread plug can go deeper
03-06-2012 03:01 PM
Ekki
I need a carb spacer

Well, actually I do not want to use a carb spacer but when I tried to install my new carb feed lines I ran into a clearance issue (see attached pics) with the Performer intake. Btw, the feed lines are original parts from Quick Fuel for my SS-680-VS carb.

Anyway. A spacer is the only (easy) workaround I can think of right now. I guess a 0.5" spacer won't change the setup dramatically. Any recommendations for good ones or parts to avoid?

Thanks!



Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.