Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> the frount end shimmed
User Name
lost password?   |   register now

Thread: the frount end shimmed Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-15-2012 11:04 AM
MARTINSR Front end shimmy can be only a few things on that car, but likely a product of a few working (or not working in this case) together. Were the king pins done correctly? There could be a little slop in them. The quickest fix hopefully is setting the proper toe, if it is toed in or out too much each wheel tries to go in a different direction, thus the shimmy. Worn tie rod ends can do the same thing. Jack up one front tire and grabbing the wheel with both hands, one in front and one in rear and pulling toward you with the right hand and pushing away with the left and then visa versa going back and forth, is there any play? Have someone do this for you while you are looking right at the tie rod end. If you see ANY play in the tie rod end, it needs replacing. Moving the wheel only a tiny fraction of an inch should transfer that tiny fraction of an inch to the tie rod. If the tie rod stays still while the wheel and spindle move if only a TINY bit, that is wear in the tie rod end. It takes very very little movement like this at 60 mph to make the wheel want to take off in a different direction and cause shimmy. Same for the king pins, same for the drag link, and the wishbone. The wishbone has a rubber mount so it will move a little, but not much. But the tie rod and drag link ends should be tight at a drum.

The wheel bearings could also be loose, again, move that tire back and forth with the hub cap off so you can see the end of the spindle and nut, if the hub moves AT ALL at that point, your wheels could be trying to go off in another direction, not good.

One or all of these things could be causing your problem. But just being sure the bearings are tight enough, and the toe is good (toe in about an eighth of an inch or so) can do wonders.

04-15-2012 10:42 AM
the frount end shimmed

I went to Vegas last weekend, about 400 miles round trip, in the 41' found out that at about 60 mph the front end shimmed. Getting ready for the trip I had the wheels balanced to avoid such difficulties. The car is stock, I have replaced the kingpins is all. What or where should I look next to solve this symptom.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:34 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.