Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Paint steps and tips
User Name
Password
lost password?   |   register now

Thread: Paint steps and tips Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2012 11:47 AM
Syn77 Well guys thx for the reply but I, was, aware of the time this by, all means is well worth it, I, wouldnt have, spent, money, on, basically a new truck if I didnt know, what I was getting into I really just needed a general idea of how it should be like sand to metal body, work then epoxy high primer, sand primer stuff like, that, ive done some resarch but ive have like 4 or 5 months until I start school
04-28-2012 09:04 AM
Localboy808
Quote:
Originally Posted by oldBodyman
RESEARCH IT. +1

"I figured might as well put in the time to paint it, problem is I've never painted or preped any car for paint I know little about what I want but not how to do it. I want to take it the bare metal epoxy it and use a basecoat the truck is gonna be blue or silver any tips would be helpful"

You asked for it.

Realise you are going to spend a minimum of 100 hours of hands-on work time + bodywork on this. That does not count smoke stops, coffee breaks or sucking suds with your buddies or cleaning up, its 100 hours of hands-on work and 100 hours of everything else in your life you are not doing.

It's dirty, messy work that smells bad, tastes worse and gets onto and into everything so figure on wearing painter's tyvek jump suits to throw away or get divorced over a washer/dryer combo.

Going down to metal would also mean pulling the windshield & backglass (they may break) and reaming out all of the seam sealer. Add another $500 for sealer, gun and sundries.

Sorry to rain on your parade but I have seen too many people start too many projects and thrown in the towel half-way thru because they did not realise how much work and time this takes.
Everything you say is 100% right. But if you have the desire and drive to do it it makes it all much easier. When I'm working on my car in the garage it's relaxing to me. I could come home after a long day at work. And still put in another 3 or 4 hours in the garage and not even think about of it.

So if you want it? Go for it! But listen to these guys. It's hard work but very rewarding. Plus you will save a ton of cash doing it yourself. And have the satisfaction knowing you did it yourself! Or you could just take it to One Day paint.
04-28-2012 08:53 AM
oldBodyman RESEARCH IT. +1

"I figured might as well put in the time to paint it, problem is I've never painted or preped any car for paint I know little about what I want but not how to do it. I want to take it the bare metal epoxy it and use a basecoat the truck is gonna be blue or silver any tips would be helpful"

You asked for it.

Realise you are going to spend a minimum of 100 hours of hands-on work time + bodywork on this. That does not count smoke stops, coffee breaks or sucking suds with your buddies or cleaning up, its 100 hours of hands-on work and 100 hours of everything else in your life you are not doing.

It's dirty, messy work that smells bad, tastes worse and gets onto and into everything so figure on wearing painter's tyvek jump suits to throw away or get divorced over a washer/dryer combo.

Going down to metal would also mean pulling the windshield & backglass (they may break) and reaming out all of the seam sealer. Add another $500 for sealer, gun and sundries.

Sorry to rain on your parade but I have seen too many people start too many projects and thrown in the towel half-way thru because they did not realise how much work and time this takes.
04-28-2012 08:09 AM
novafreek6872
Quote:
Originally Posted by Syn77
problem is I've never painted or preped any car for paint I know little about what I want but not how to do it.
RESEARCH IT. Plenty of sites and videos and books detailing all the finer points of painting your car. Youre not going to get the knowledge you need in a few quick replies on this board.

Not trying to be rude, but there is a whole lot to this and you need to take the time to learn all about it before you dive in.

Andy
04-27-2012 11:48 PM
Syn77 Oh and another thing what should I paint first I'm bed lining under the bed and cab
04-27-2012 11:23 PM
Localboy808 Read a lot of the posts here. Watch videos on YouTube. Make sure your surface is very clean before you spray. Use a good wax remover. You can get a bottle from the auto paint supplier. One bottle goes a long way.

I used a direct to metal primer. Then 2 coats of base. And two coats of clear. Follow the instruction on the cans of paint. Get an activator that matches the temps you will be painting in. Dont rush! Let the coats flash/dry between coats! Usually about 15 to 30 mins. Depending on the temp in your booth/garage. A tip I saw was to touch an area of overspray to see how tacky your last coat is. You don't want to spray the next coat if the one that's on there is still wet.

Is the bed liner a spray on or roll on? Either way you will get overspray on it unless you tape it off. Not sure if you care? But if you do and it's a roll on maybe do the liner last? Especially if it's a roll on. Less chance of getting it on your new paint job. If its a spray on I'd personally do that first. Then paint my car. Maybe someone with more personal experience can chime in. Best of luck!
04-27-2012 07:44 PM
Syn77 Oh and another thing what should I paint first I'm bed lining under the bed and cab
04-27-2012 07:40 PM
Syn77
Paint steps and tips

So im painting my truck its a 77 k10 i recked it some girl hit me and bent my frame. I couldnt get rid of my truck go so I bought a frame that was in great shape and planned on putting it back together, so since im gonna have everything off I figured might as well put in the time to paint it, problem is I've never painted or preped any car for paint I know little about what I want but not how to do it. I want to take it the bare metal epoxy it and use a basecoat the truck is gonna be blue or silver any tips would be helpful

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.