Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> A QUESTION FOR 64-65 malibu/chevelle owners
User Name
Password
lost password?   |   register now

Thread: A QUESTION FOR 64-65 malibu/chevelle owners Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-14-2012 07:57 AM
MARTINSR This is true, I was using the outside of the wheel cover on the Chevelle and it is most likely at least 15".

But still well within the boundaries of "close enough" for this purpose I am hoping.

By the way Fozzie I am doing the exact same thing on my truck in that I am looking at making my wheel openings the same as a 53-55 or 56-57 Vette. I am not at that point where I am doing any cutting so right now while dreaming of the project I am keeping my eye out for these cars and just standing back and eye balling them thinking about it. At a recent visit to a local museum I took these photos for the project.

I hope to literally be able to take a pattern off a real car just for kicks but if I can't find someone willing to let me I will be using photos like these.

Back before photo shop I use to blow up a photo and then cut measuring carefully a known, and chop the top or section the body of the car or truck in the photo. Standing back and looking at mocked up modifications is one of the most important things you can do when customizing a car. All too often this is done in hast and the cutting and welding is done before a real good look has been done. A photo cut up on your dining table and taped or glued together is one way to mock up your cars modification and "stand back" and get a good look at it. Now this is just one dimensional and you can't walk around and get different angles of it, but it is better than nothing.

I have one of these photos on the wall of my garage that I did of my truck 15 years ago, hopefully I will be back on the truck in not too long. Right now it's just inspiration to finish the project I am on.


Brian
05-14-2012 02:33 AM
cobalt327
Quote:
Originally Posted by hotrod fozzie
thank you for the help seems very logical , I am glad you took the time to help me out!!!
One small addition- a 14" steel Chevy wheel (as used on my '80 Malibu), when viewed from the side is about 15-3/8" in diameter when taking the bead retention flange into account.
05-13-2012 07:19 PM
MARTINSR Your welcome, now have fun!

Brian
05-13-2012 07:10 PM
hotrod fozzie thank you for the help seems very logical , I am glad you took the time to help me out!!!
05-13-2012 10:40 AM
MARTINSR Take the measurements right off this photo.



Right on your computer monitor, measure a "known" like the diameter of the wheel. We know it's a 14" wheel. If you take a piece of paper and put it up on your monitor marking off what the diameter of the wheel is you now have a standard to go by. You then put a piece of paper on the screen across from the front of the wheel well to the rear of the wheel well and using your standard measure the distance from the line up to the arch. I find that it is almost exactly half as far as the diameter of the wheel making that measurement you are after to be 7". Yes this is kinda crude and it may be off a bit but what does it matter if you are doing a customer mod anyway?

What looks good on your truck is what really matters. Taking this rough measurement and mocking it up somehow on your truck you can get a good idea of how it will look. Mock it up with cardboard or something, be sure that the cardboard is the same color as the truck so it doesn't give you some illusion and get it out side so you can stand back and look at it.

Brian
05-13-2012 08:52 AM
hotrod fozzie back to the top
01-06-2012 05:08 PM
hotrod fozzie
A QUESTION FOR 64-65 malibu/chevelle owners

I am building a custom truck and like the height of the rear wheel archs on the 64 and 65 chevelle , can someone who owns one do me a favor? Run a string line from the front to the back of the quarter panel at the bottom and give me the measurement up to the center of the wheel arch? It would be like if you lowered a car and measured from the ground up to see how much lower you are except your not going from the ground but measuring up from the string I HOPE THIS MAKES SENSE AND YOU CAN HELP PLEASE!!!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.