Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Drivshaft Length and Balance?
User Name
Password
lost password?   |   register now

Thread: Drivshaft Length and Balance? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-17-2012 10:06 AM
Doubleclutch
Thanks Guys

I'm getting the same advice locally here. The 2 inches is excessive so I need about 1/2 added. Also the retube and balance is relatively inexpensive--its the u-joint yokes that add up.
05-14-2012 06:32 PM
prostreet6t9 Remove the Shaft and check it for the correct length. Any "sectioned/cutting" is a bad deal and is a good idea to fix. Take it to a Driveline shop and get it Retubed "longer if needed".
05-14-2012 01:53 PM
MARTINSR
Quote:
Originally Posted by Doubleclutch
Assuming its true, can there be a balance problem enough to shake a CD out of track at 70?

Thanks as always Chuck

In a word YES! Just the weld it's self (weight) I imagine can set it off, the weights I have had installed ballancing shafts I have modified were not very big.

This doesn't sound very good at all.

Brian
05-14-2012 12:35 PM
willys36@aol.com Amateurish welds on the driveshaft aren't good. Since it looks like an amateur job, have you checked the phasing of the U-joints? Are they set up in the same plane?
05-14-2012 12:04 PM
Doubleclutch
Drivshaft Length and Balance?

Hi Guys

I have a 70 Buick with a built 455 that has a 65-70 MPH and up vibration. I have gone around and around with the tire balance guy and he says after a couple of sessions to look for something else. Under the car I have two problems with the driveshaft. This is a conversion from a 350 to a 455 with a TH 400.

First is there seems to be an excessive amount if sleeve showing at the tailshaft. I have 2 inches showing with weight on the wheels. I searched the site and it shows 1 1/2 is recommended. I assume the extra 1/2 is OK with my HP around 350 since its holding but looks excessive.

Second is the driveshaft has been sectioned/cut at the rear yoke. The welding looks very amaturish at the join. I'm going to try to spin it and see if its true. Assuming its true, can there be a balance problem enough to shake a CD out of track at 70?

Thanks as always Chuck

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.