Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> isky cam selection
User Name
Password
lost password?   |   register now

Thread: isky cam selection Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-16-2012 05:07 PM
louis165
Quote:
Originally Posted by lmsport
247@.050 is big for a street car with power brakes.
I would lean toward something no more than 230@.050 on 108
Thanks imsport I think your wright I was more focused on the DCR ..I found another one but can't seem to find the part # Isky cam 282/294 234/246 @ 50 530/550 lift 106/110 LSA Intake open 7, exhaust open 47, Intake close 53 exhaust close 13. All timing figures at 50 duration.
05-16-2012 03:59 PM
lmsport 247@.050 is big for a street car with power brakes.
I would lean toward something no more than 230@.050 on 108
05-16-2012 01:07 PM
louis165
Quote:
Originally Posted by ap72
If you want an isky cam call isky for a recomendation. Don't be affraid to ask questions and expect to spend more than 3 minutes on the phone.
That's what I was affraid of .. thanks ap.. I found this one seem to be close.. but I will call to make sure..:..... : 201027 GRIND NUMBER: z-27 ENGINE INFO: CHEVY SMALL BLOCK V8 265-283-302-305-307-327-350-400 CU.INCHES APPLICATION:

SPECIAL REMARKS: SOLID PRODUCT USE: STREET/STRIP

RPM RANGE: 2800-6800 Valve lift is calculated with zero lash and rocker ratio of 1.5

INTAKE TIMING DURATION: 282 deg. OPEN: 33 BEFORE TDC CLOSE: 69 AFTER BDC CAM LIFT: .338" VALVE LIFT: .507" VALVE LASH: .018 HOT .02 COLD

EXHAUST TIMING DURATION: 282 deg. OPEN: 69 BEFORE BDC CLOSE: 33 AFTER TDC CAM LIFT: .338" VALVE LIFT: .507" VALVE LASH: .018 HOT .02 COLD

LOBE CENTER: 108 deg. OVERLAP: 66 deg. CAM ADVANCE: 0 deg. THE ABOVE TIMING IS CHECKED AT .020 (OPEN) LIFTER RISE .020 (CLOSE)

The following timing is taken at .050" lifter rise and gives a more accurate determination of camshaft position. INTAKE DURATION: 247 deg. OPEN: 15.5 BEFORE TDC CLOSE: 51.5 AFTER BDC

EXHAUST DURATION: 247 deg. OPEN: 51.5 BEFORE BDC CLOSE: 15.5 AFTER TDC

RECOMMENDED ISKY CAM KIT PARTS AND SETUP INFORMATION

LIFTERS: 202-H LIFTER TYPE: SOLID SPRING: 205-D TYPE: SINGLE W/DAMPER DIA.: 1.250" RATE: 310 lbs per inch INSTALLED HEIGHT: 1.700" SEAT PRESSURE: 115 lbs OPEN PRESSURE: 268 lbs COIL BIND: 1.160" SPRING SHIMS: # 4 STEEL RETAINERS: 707-ST TITANIUM RETAINERS: PUSHRODS: 203-HG TYPE: NON-ADJ HEAT TREATED LENGTH: 7.781" DIA.: 5/16" ROCKER ARMS: 204 TYPE: ROLLER RATIO: 1.5 VALVE LOCKS: VL-32 VALVE LOCKS: VL-32 REV KIT:

home | what's new | tech info | news | catalog | apparel | about | contact
05-16-2012 12:54 PM
ap72 If you want an isky cam call isky for a recomendation. Don't be affraid to ask questions and expect to spend more than 3 minutes on the phone.
05-16-2012 12:50 PM
louis165 My bad :...:.........lol
05-16-2012 12:42 PM
ap72 Lmao. You used a simple calculator to determine that your ivc is set in stone at 53? That's pretty funny.
05-16-2012 12:07 PM
louis165
isky cam selection

I need a cam that closes intake @ 53. According to KB. Cal. Sbc 350 std bore .trw flat tops 3.5 cc deck hight .020 . .. head gaskets 1094 .015 .heads are edelbrock e-tec 200 . Rpm air gap . Holley 750 vac 700.r trans 2800 stall .. tires 25.5 ..car is 3200 lbs. Power brakes ..this is not a daily driver .. Scr .. 10.5.. Scr..8.22 thanks for any help guys

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.