Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> CC-ing chambers with clay
User Name
Password
lost password?   |   register now

Thread: CC-ing chambers with clay Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-31-2012 10:11 PM
ap72 i use a 10cc syringe but it takes a while and its a pita to get right as you have to keep refilling it.
05-31-2012 07:33 PM
spinn Emergency rooms will dispense a 10cc graduated syringe for free.

A CD jacket clear top with a small hole works fine.
05-31-2012 04:44 PM
cobalt327 It will be accurate to maybe plus or minus a cc or so. I wouldn't use it to equalize chamber volumes- you need better accuracy for that. But for getting an estimate for figuring compression ratios, it's fine.

I don't know if you were going to smash the clay down into the beaker to measure the volume, but the easier way is to add a known volume of water to the beaker- enough to cover the clay- and then ease the clay down into the beaker and see the lever the water rises to. That level, minus the starting amount of water, will be the chamber volume in cc.
05-31-2012 02:21 PM
ganymede Thanx for input everyone. I bought non-hardening modeling clay and a kitchen beaker at WalMart & Hobby Lobby for $8 today(clay was 30% off). The beaker is graduated in 2 ml. I believe it can just as accurate if I do it right. I know several hotrodders have done it. Wipe chamber with silicone lube so it doesn't stick. Lightly pound it in. Level it and drop in beaker. If it comes close to 63 to 64 cc it should be accurate.
05-31-2012 01:02 PM
F-BIRD'88 Many local pharmacies carry 100ML graduated cylinders with base in glass or plastic. The plastic ones are dirt cheap. Plenty accurate for this.
05-30-2012 11:20 PM
cdminter59
CC-ing heads

I have never in my life heard of anyone cc-ing a head with clay! I am 60 years old.
05-29-2012 08:47 PM
ganymede ha, ha. Job is this weekend. I don't have time to order a burette. Should be easy to level the clay with a machinist straight-edge. Going to try .015 rubber coated steel shims.
05-29-2012 06:53 PM
cobalt327
Quote:
Originally Posted by ganymede
Is clay accurate?...dropped into a marked beaker of course.
Sure, you could measure the volume by displacing the water in a beaker if it's accurately graduated. The trick is to get the clay level w/the surface of the deck- even a small amount over or under will skew the results.

Any reason you don't want to use the more traditional method of colored water/isopropyl alky mix, a piece of clear plexiglass or a CD w/the plating scraped off, a dab of vaselene, and a 10cc syringe from the vet or pharmacy?
05-29-2012 06:53 PM
LATECH It can be accurate , but it is better for checking valve clearnce.
Just CC your heads with water by covering the chamber with a stiff piece of plexiglass that has a fill hole drilled in it. I used an old CD ,it was a clear one that was used as a spacer or in a pack of new CD-rw that I bought.
I bought a Beret from Online science mall on e bay for like 25 bucks.
It was easy to check, and accurate once I had the right stuff.
Some guys mix something with the water to help break surface tension, so it gives an absolutley perfect reading.I didnt use anything but water. I just needed to know I was real close.Got both heads shaved and ended up at 82 CC s on each one.I checked all 8 to be sure they were all even before i had them milled, just to keep the record straight.
05-29-2012 05:39 PM
ganymede
CC-ing chambers with clay

Is clay accurate?...dropped into a marked beaker of course.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:19 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.