|10-29-2012 04:13 AM|
Good stuff. Its nice to have finally solved the problem.
|10-29-2012 03:23 AM|
|hobby28||I thought I would post a follow up to this old post. I installed a fuel pressure regulator and shut the fuel pressure down to 4.5lbs. The problem went away immediately, I raced the rest of the year and never had anymore trouble. Thanks for all the help guys.|
|06-12-2012 02:53 AM|
I have a high presure Edelbrock mechanical fuel pump rated at 10 psi on my 347 The holley 650 max operating pressure is 6 psi so i installed an adjustable holley regulator and set the pressure to 5.5 psi and have not had any issues at all using the standard float height measurement I also installed a $10 fuel pressure gauge inline next to the carb so you can watch the pressure while adjusting the regulator. If you had a fuel pressure gauge you could see at a glance when you are at wide open throttle , maybe you could monitor that and see what is happening.
|06-11-2012 11:15 PM|
|06-11-2012 11:01 PM|
|hobby28||I called Sean Murphy with SMI carbs today and the first thing he asked was how much fuel pressure I have. I told him 8lbs and he told me to drop it to 5lbs and the problem would go away, and I was flooding the engine out by blowing by the needle and seat. It makes sense so I will install a regulator and see what happens, I am also going to try and keep some heat off the carb. Thanks for all the input.|
|06-11-2012 11:20 AM|
|boothboy||You have two previous post mentioning insulators between the manifold and carb and that's what I was thinking. I had the same problem with a BBC years ago. I installed the insulator and also a sheet of aluminum painted flat black on the top side. Heat was directed away from the carb. Worked like a champ. Something else to try.|
|06-11-2012 03:34 AM|
I'm going to guess you are already using an insulator between the carb and intake. You could also try blocking the heat crossover under the plenum. Use a good quality mechanical fuel pump.
|06-10-2012 10:29 PM|
|hobby28||I am not running a fuel pressure regulator and have raced for 10 years without one. The vent at the fuel cell is clear. The float level is good and the needle and seat appear free and in good shape. I don't have an isolator on the intake we a forced to run an aluminum carb adaptor from a performer eps intake to a 2 barrel rochester.|
|06-10-2012 09:30 PM|
2. Check the vent @ the fuel cell.
3. Have you checked the float level on the carb?
4. Do you have a heat isolator between the intake & carb?
5. Check the needle & seat in the carb, it may be sticking.
|06-10-2012 08:03 PM|
|hobby28||Guys my problem is back again, last night was the first hot night at the race track and the same sputter was back on restarts. The car ran awesome after it stumbled and it went the back of the pack. It sputters and almost dies, then it will fire just a little, then it clears itself and runs great until the next caution and restart. I changed the engine late season last year and the problem went away and i am still running that engine, so i am stumped. The fuel pressure gauge fluctuates alot under load, it will go from 8psi clear down to 3psi sometimes. Do you think i could be sucking air in the fuel line somewhere, and how would you test it. Or am i boiling the fuel in the line and once fresh fuel gets pumped up there it takes off?|
|07-26-2011 01:36 AM|
Is there any rubber connecting hose on the feed side of the fuel pump.
It may be collapsing and or kinking with heat. Age.
|07-26-2011 01:17 AM|
|mike 96 ws6||
|07-25-2011 10:06 PM|
I tracked a faulty ignition module down which missed when it became warm by using an inductive timing light with the pickup clipped to the high voltage coil lead (not the plug leads) and when it starts to miss you can look at the strobe light to see if it has gone out and comes back on. You will need to duct tape the light to somewhere visible so you can glance at the light while powering up the engine on the track. Sometines its hard to tell between a fuel misfire and an electrical misfire but the timing light will still keep on strobing if the ignition system is up to scratch and the 3 psi fuel is starving your engine.
|07-25-2011 08:53 PM|
|hobby28||A little update on the engine. I replaced the pickup coil before i went to the track and it fell flat on its face in the heat race. I started the feature and quickly started having issues. I was at the back so i had time to troubleshoot, i watched the fuel pressure gauge and when it cuts out the fuel pressure drops down to 3 psi or lower. It is now getting worse and completely dieing, but when you let the clutch out to roll the engine over while coasting the engine fires when the fuel pressure comes up. I had a 110 gph carter fuel pump that was about 6 yrs old and the fuel pressure was fluctuating with rpm it would go from 7 down to 6. So i replaced the fuel pump with a holley 110 gph and emptied the fuel cell to check and replace the fuel pickup. The car seems to run ok at the shop like usual is there anything else i need to look at, it will be 2 weeks before i can race again.|
|07-21-2011 07:02 AM|
|DoubleVision||You are using heat sink compound on the bottom of the module?|
|This thread has more than 15 replies. Click here to review the whole thread.|