Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Door Skin Patch Panel Install Question
User Name
Password
lost password?   |   register now

Thread: Door Skin Patch Panel Install Question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-13-2012 09:29 AM
tech69 great advice, guys and nice work.
06-12-2012 05:03 PM
deadbodyman First you start with the outer skin get it fitted with the lips folded at a 90 degree angle , use a couple drill screws to hold it in place ,they'll also help you remove and replace it in the same spot every time...Once the outer skin is set in place you can remove the inner piece and know exactly where it goes according to the outterskin thats already in place...When you have the inner all welded in you remove the outter skin and and work the back side of the inner you just welded in,then get it epoxied then epoxy the outter skins backside and put it on with the screws (I like using a flanged lap joint so it wont warp plus you need it when you use screws...fold the skin over with the skinning hammer or a cheap body hammer that you ground one side straight so it will skin better (but not near as good as a skinning hammer) and the dolly then weld up the seam...I use plug welds every two inches and then weld the seam all the way across one spot weld at a time...
06-12-2012 01:43 PM
MARTINSR Here is a "Basics" on door skins (click here) which is basically what you are doing, half of a door skin. Sanding the edge as described in the "basics" would be a big help so it will fold easier.

Brian
06-12-2012 11:01 AM
tech69 I like to view it as moving it in 3 increments. Do one increment all over, then do two all over, then hammer it down flat. This way you won't damage the outer skin. When you're doing a patch skin sometimes it's gonna wanna suck down on you so you have to prop it up to the proper contour before welding, especially true if you flange the existing old metal. If you flange the lower small patch like that you may stretch it and the bottom edge of the door won't be straight. Another option is a backing strip but I usually just flange it and deal with propping it up when needed. Not usually a big deal but something to account for. Also make sure your door frame has an even flange that's straight. If it's not straight your metal you are folding may follow it's shape.
06-12-2012 08:39 AM
boatbob2
door skin.......

Hi,when i did this,i clamped the door skin to match up with the cut skin,then marked the bottom (NEW PIECE),then made my bottom fold before welding the top seam,i made the NEW PIECE about 1/4 inch longer,then ground that piece to match the original door skin.
06-12-2012 08:21 AM
35WINDOW There is more than one way to skin a Cat-I use a regular Body Hammer, but they make a Hammer specifically to do this-anyway, I will start at one end of the 'Skin, and start the edge folding with the Hammer, backing it with either a rubber Dolley, or a rubber Trowel so that I don't mar the outer skin, slowly working the edge over the inner Door Panel-take it slow, fold a little at a time, and work your way around the Door-you don't want to try to fold it all over in one place, just work your way around the Door-

Here's what a Door Skin Hammer looks like-
06-12-2012 07:39 AM
Houston54
Door Skin Patch Panel Install Question

I am trying to repair the bottom of a 1958 Chevy truck door. I have installed the inner door patch panel and am at the point where I am ready to install the outer patch panel but would appreciate some guideance from someone familar with this repair.

I have tacked the upper seam in place but the proper/best method to fold the edges over the door shell escapes me.

Anyone out there familar with this?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.