Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Budget Cut SBC Build Lots of parts what now?
User Name
Password
lost password?   |   register now

Thread: Budget Cut SBC Build Lots of parts what now? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-21-2012 07:06 AM
AutoGear Build what you can with what you've got...its what hot rodding is all about. Whatever you build will be a kick in the butt for that old camaro. One thing to think about; if you go too crazy, and money is already tight, you've gotta feed your beast too...gas won't be getting cheaper.

Sorry to hear about your situation; you could always sell off some parts, go low compression and a blower or junkyard turbo setup

Remember: center mass & double tap (Sig P226 in .40 and P220 in .45 here)
06-21-2012 12:24 AM
vinniekq2
engine choice

How fast do you want to go?If its just for fun then start with the 406.I built a very very low budget 406 for a friend.Torker intake,bought used,750 carter carb,bought used,mild hydraulic flat tappit cam,small tube headers,3.36 gears,turbo 350.In a 1978 monte carlo the car ran a best of 13.30s at 99 to 100 mph. decent mileage for a daily driver.also it had stock 400 heads with a 3 angle valve job
Ive never tried 1/8 mile. I doubt you will hurt a mild 400 racing 1/8 mile.
the 383 has better parts if you decide to go wild.
06-15-2012 05:33 PM
High School Hot Rod I'm in Dickinson North Dakota, and it is pretty crazy around here in good and bad ways. Many stores are closing because they can't compete with the wages the rigs offer...even mcdonalds closed in williston. Anyone can get a $20 an hour job but you have to find a place to live. Also you are working and living with and around the scum of the earth. I'm a big guy at 6'3 and 230 and I carry a concealed weapon. It really is the modern gold rush.

But on to my engine, would you rather use the stock 400 crank and rods and sell the 383 short block, or use bearing spacers and use the scat crank and 5.7 rods from the 383. Then of course what is the chances of putting 400 pistons on the end of the rods and still being with 50 grams of the previous balance?
06-15-2012 02:20 PM
spinn neighboor has a cdl and moved with a oil company based in texas. Made more in a summer than i make in a year.

He follows these oil recovery operations around. Only in a area for a couple years at a time. Hauls contaminated dirt. Good job to see the country if you have no ties.

It is your tree you are sitting in it. Build what you can and enjoy.

If you have a 400 there is no reason not to build it.
06-15-2012 01:29 PM
against all odds Could you tell me about the work situation where you're at? Is it really that out of control(in a good way)?


What is your budget and does the camaro have an engine in it now?
06-15-2012 01:24 PM
High School Hot Rod
Budget Cut SBC Build Lots of parts what now?

Just when I have my build done on paper and my summit shopping cart finished my rent got jacked way due to the need for housing near the bakan oil fields. So my full roller 383 is a thing of the past.

Here is what I have:
383 short block scat crank 5.7 rods hyper pistons, ported 441 heads w/ hyd. flat springs good to .500 lift, weiand dual plane, trick flow 23 195cc w/ SR springs good for .650 lift, howards SR cam 247/249 .585/.585, stock 400 intake to oil pan bored 30 over never been reassembled.

The car is a 1980 camaro backed by a turbo 350, 3.90 gears, and 26in MT drag radials. Street car that will see the 1/8th mile.

What would you build Im thinking of building the 406, Im thinking I might change the springs in the trick flow's for solid ft and go that route with cheap 30 over pistons and the stock 400 rod and crank and selling the 383 with the 441's on top of it

thanks, again

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.