Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Thoughts on a cam
User Name
lost password?   |   register now

Thread: Thoughts on a cam Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-20-2012 06:25 PM
Mr. P-Body For the 4-speed, I would agree with Comp, if a flat hydraulic is what you want. XE274H is a very popular grind and makes power to 6,000 without problem in the small block. It will be "lumpy". Springs should be about 120 at the seat. Duals are the best idea. We use Sealed Power lifters on these cams.

Vinnie has a good point. A flat tappet solid is a "happy medium" between a hydraulic and a solid roller. The XE grinds are excellent. Comp's solids seem to be rated a little higher in duration than their hydraulics. They don't "act" it. If you're thinking "230 @ .050", go for 236. Great manners and a broad power band. We've used many in Pontiacs, but also a few in small blocks, with similar results.

Use lifters with the EDM hole in the bottom (Comp has them, as does Crower and others). This will insure lobe "life". If your budget can stand it, go for the 4-7 "swap" (firing order change).

Springs need to be 140-150 at the seat. A true dual spring is called for. Break the flat tappet (hydraulic OR solid) cams "in" with only the outer springs installed. Install the inners and run it again.


06-20-2012 02:31 PM

would you consider using a flat tappet solid cam?smoother idle and good throttle response.Talk direct to comp or the manufacturer you choose.Spend a little time explaining "exactly" what you expect. Ask three times and see where the overlap comes,pun intended.Lobe separation angle and intake lobe centre line are just as important as lift and duration.With AFR heads you dont need a lot of cam. Talk to afr and look at their website for results they get with their products.
AFR was an excellent choice,your engine will make a lot of usable power
06-16-2012 12:00 PM
prostcelica Thanks for the input guys. I think ill pass on the marine cam. Comp just replied to my email and recomended there extreme energy 274. Probably best to listen to the guys that grind the cam.

Anybody out there have this cam?? if so how is it for power?? idle quality??
06-16-2012 11:11 AM
probird my favorite cam for hot rods has been the comp cams magnum 280.
great sound and power. good vacuum, etc. Theres probably better cam profiles made now but your best bet is to call comp and ask there teck line.
They make this stuff.
Don't forget its the total package to make the best driver.
06-16-2012 11:04 AM
painted jester That cam also has a smoother idle and strong bottom end , Designed specifically for marine performance!!! And exhaust in water that restricts flow!!!!

I'd pass on the recommendation to run the marine cam on the street , Those are just my thoughts!

06-16-2012 10:50 AM
cobalt327 I don't see the AFR's needing anything like that kind of split duration, the exhaust side of those heads is better than that.

I think it will want more gear than that.
06-16-2012 09:48 AM
Thoughts on a cam

I had i guy (that seems to know what he talking about) recomend a comp extreme marine cam. XM278H

Duration @.50 234 in. - 244 ex.
Lift .498in .5ex
LSA 112

The plan is sbc 350 .030 over, AFR 180cc heads, RPM air gap, Holley 670, 1 5/8 headers. 4 gear manual , ford 9" posi 355. It is a street car that will see the striip couple times a year. What do you guys think about the cam??

I know a roller would be better but I only have so much $$$ to spend

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:15 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.