|06-19-2012 03:29 PM|
What is the initial timing set at? You can do a little research on timing, here is a page that may help you get up to speed (ha) w/the effects of timing on the overall performance of the engine.
Bottom line is I'm thinking you may not have enough initial timing. This may be because the dynamic compression ratio has you up against a detonation problem; a quick fix for that is to use less initial timing- but that can have a very bad effect on performance.
You need to see where you are now; if it's low I would suggest you try around 16 degrees BTDC, but this may require you to limit the mechanical advance so the total timing (initial plus mechanical) doesn't exceed 36 degrees or so.
I'd also suggest along w/a compression and/or leakdown test that you put a vacuum gauge on the engine and see what the vacuum is at idle. Check for vacuum leaks if there's any chance you may have one. The engine should idle pretty smooth w/that cam, so if it's loping/missing at idle, there's a problem that may be ignition (or possible carb) related.
|06-19-2012 01:53 PM|
|F-BIRD'88||The torker II manifold is a dog for this application.|
|06-19-2012 09:15 AM|
I knew this would come in handy. I started a word document with all my specs. It's a work in progress so bear with me.
GM Block Casting Number
1969-1979 || 350 ci. || 185 low power || 370 high power || 2 or 4 Bolt Main || car, truck, Vette
Suffix Code on Block Behind Alternator
TKB ||1976 || 350 || conv.cab || VIN: L LS9 || HP: 165 || 4 BBLS || Applications: C-10 & 1500
TKB ||1979 || 350 || conv. cab, m/t || VIN: L LS9 || HP: 165 || 4 BBLS || Applications: C-30 & 3500
Heads Casting Number
58cc chambers, 1.84/1.50 valves @ stock
Has had 1.97 intake valves put it in
650 CFM Holley
Edelbrock Torquer 2 Intake
4:56 rear end posi (Had stock gears in it before I did a rear end swap)
I do not know anything about the torque converter.
|06-19-2012 09:15 AM|
Do a compression test. Anything less than 120psi is bad.
What camshaft do you have? If its a Comp, I would look there.
|06-19-2012 09:04 AM|
The cam specs are going to be very important, as is the rear gear ratio and torque converter stall speed (they need to be matched); a stock '74 Nova rear end may be geared very high (low numerically, like a 2.73). Next is the timing curve and how much initial timing is being used, as well as the total timing.
You can use this page as a guide for giving info- and more info is better than less.
|06-19-2012 09:00 AM|
|06-19-2012 08:58 AM|
Ok fellas, my bad... I didn't realize how much I was loosing with these pistons. That being said, the car runs terrible to be at 9anything:1. It's almost embarrassing.
It just doesn't have the power it should. My dad and I have had 3 different carburetors, 2 new distributors, the list goes on.
When I take of it's just slow as all get out. My old 97 Taurus 3.0 V6 was quicker off the line.
A buddy of mine says I should change the torque converter, but hell IDK. Any ideas/suggestions?
|06-19-2012 08:36 AM|
txdude350, what is the engine doing or not doing that has led you here?
|06-19-2012 06:07 AM|
Looks like a typical 12cc dish to me.
plus the piston is most likely down 0.020" below deck. Maybe more.
727cc/cylinder (355 cid)
8cc head gasket (0.040")
4cc deck height
(727+64+8+4+12) / (64+8+4+12)= 9.26
with 58 cc heads cr will be around 9.86:1.
Would need 48cc heads to get 11:1 with those pistons and a typical head gasket.
|06-18-2012 11:52 PM|
|06-18-2012 04:17 PM|
|6426yy||With that big of a dish you can't be at 11:1. I've also ran 305 heads on a dish piston 350 with no problems, on junk gas in a 4000 pound truck with 3.08 gears no less. I'm not sure what problem you were having before but I don't think you have too high of compression.|
|06-18-2012 03:50 PM|
|lmsport||A stock replacement piston has about 8cc volume.|
|06-18-2012 03:34 PM|
I don't know... I just swear that this problem is mechanical. I have ruled out electrical issues. Maybe I'll go get the heads checked out.
But with the stock 58cc and about a -5 cc piston (guy at machine shop guesstimate) I am getting over 11:1 CR. I figured this was the problem.
I think the only way to be sure is to actually check the volume of everything.
|06-18-2012 02:57 PM|
Well... What do you think about this that I found. I have 416 heads btw
There's a fella over on HotRodders.Com that swears by 416 reworked heads, FireBird88 I believe is his handle. Do a search on that site/engine forum for 305 heads on a 350; there are a ton of posts. Butch/56sedandelivery.
Taken from This site
|06-18-2012 02:50 PM|
-12 to -15cc dish volume is typical.
9.4:1 to 9.8:1 with a .015" gasket
|This thread has more than 15 replies. Click here to review the whole thread.|