|06-27-2012 03:40 PM|
Bolt 1 goes through hole 1 on the bracket, then through the alternator, then the upper hole (looks like #2 in your picture) on the manifold.
Hole 2 on the bracket is bolted to the lower hole on the manifold that you did not number.
The bolt that holds the water pump goes on the upper bolt just like the J-bar. This braket goes on first and the J-bar is on top of it, then the washer and bolt.
The included diagram from the '70 assembly manual should answer your questions. You'll have to be the judge on the motor mounts.
This will fit in a small box so I can ship to Canada and would add the difference to the price.
|06-27-2012 03:11 PM|
|KENMO||So this is how it would connect - hole 1 to bolt 1, hole 2 to bolt 2, hole 3 to water pump?|
|06-27-2012 02:27 PM|
Do you think it'll clear stock C1 engine mounts?
PS: I'm in Canada....
|06-27-2012 12:15 PM|
I thought that it looked familiar so went up in the loft and looked around. This is the piece that you need. You can have it for $25 including the shipping in the Continental US.
You can see how it wedges the alternator between the manifold and the bracket at the upper hole while the lower hole bolts into the manifold to stabilize it. The other hole goes to the water pump bolt.
Actually, the way you currently have it, you've moved the alternator ~3/8" forward (thickness of the bracket) and outwards a bit from the stock arrangement because the bottom hole of the alternator should be in the upper manifold bolt hole. Hope this helps.
|06-27-2012 10:45 AM|
Yes, that's the one. I looked at my assembly manual and yes, a similar bracket was used on the '70 Corvette with the forward bolt holes.
|06-27-2012 09:16 AM|
|06-26-2012 08:59 PM|
There were a couple different manifolds with forward holes.
On a '65 Vette with A/C, there is a bracket that extends from the water pump and meets the lower hole of the manifold. The alternator is bolted to the manifold through the upper hole and the other bracket that extends from the water pump sits in front of the alternator wedging the base of the alternator between the bracket and manifold. A J-bar is used to tension the belt.
But the '65 Vette exhaust manifold has the top hole recessed from the bottom hole.
On manifolds with the holes as you show for the Impala, the engine typically uses the long water pump so the alternator sits further forward.
No Corvettes ever used the long water pump, but there may have been other year Corvettes that did find some way to use that manifold forward mount so check the assembly diagrams for the various years to see if you can find what will work. You may find that these other years that used that manifold had other brackets that used accessory bolt holes in the heads or on the intake manifold on the 350s.
I seem to remember having one wit hforward bolt holes and if I did it was for a Corvette and probably a '70. But it may have been a bit different.
|06-26-2012 08:02 PM|
I found this photo on E-bay and it is what my Ram Horns look like... There are no thread holes on the side for an an alternator, they are facing front....
Anyone know what bracket would be used on these Ram Horns?
|06-26-2012 04:10 PM|
The set up used on 'Vettes w/ramshorn exhaust looks like the image below, but if you don't have that manifold, just use the bracket like used from about '72-back on trucks w/ramshorns.
|06-26-2012 04:09 PM|
|cobalt327||SBC pulleys and brackets.|
|06-26-2012 12:24 PM|
You could use a Header Power Bracket with the appropriate spacers.
For an extended bracket:
or for a regular bracket:
|06-25-2012 09:46 PM|
|68NovaSS||Unless you're trying to keep it original, you could go aftermarket, ZOOPS has nice brackets for just about any accessory or application.|
|06-25-2012 07:43 PM|
|KENMO||Can someone post an image of what the correct bracket looks like? Thanks kindly...|
|06-25-2012 06:04 PM|
|S10 Racer||Yes you need to add the correct bracket to hold the alternator true to the crank. You are correct, there is a part of the bracket missing in the photo.|
|06-25-2012 06:01 PM|
|78 monte||Yea most mounting brackets have a tang for the front of the pivot bolt. There were allot of differant brackets best bet is to either go to a U-Pull-It and hunt for something or buy a bracket kit. Or order the correct bracket from a vette parts supplier.|
|This thread has more than 15 replies. Click here to review the whole thread.|