Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Surface Rust/Rust Mort...teach me please.
User Name
Password
lost password?   |   register now

Thread: Surface Rust/Rust Mort...teach me please. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-27-2012 07:23 AM
sumner41
surface rust

Quote:
Originally Posted by 78 monte
I have allot of surface rust popping up through the primer on my car.And a large patch on the roof were body work was started and never finished(not me).
A freind of mine suggested I use rust mort on the car. I am limited on body tools etc.... as I nolonger have a garage or access to a compressor(DA etc//) just an electric palm sander and a dream(...or....nightmare???).
So what would be the best method of going about fixing surface rust.Do I sand as far down as I can get then rust mort???Rust mort then sand???
Any advice would be appriciated.
My goal at this point is just to stop the rust progression and cover the car in flat black primer. I can fix dents etc.... afterwards as I go.
your problem is incorrect prep. after removing rust,there is still microscopic rust,plus bare metal will start rusting as soon as it is in contact with air. You NEED to remove rust you can see. THEN USE A METAL CONDITIONER (metal prep. Follow the directions. It will leave a faint white haze on metal. Prime. REMEMBER PRIMER IS POURUS,which is how paint adheres to it. NEVER JUST PRIMER. SEAL PRIMER WITH AT LEAST ONE COAT OF PAINT. Improper prep ALWAYS CAUSES YOUR PROBLEM. The average person thinks that removing rust that can be seen solves the problem. If not done CORRECTLY,IT ONLY MAKES IT WORSE. METAL PREP and SEAL PRIMER. PRIMER IS POURUS TO ABSORB PAINT AND UNCOATED WILL ABSORB MOISTURE, SEAL IT WITH A TOP COAT (PAINT) THAT WILL NOT ABSORB MOISTURE. I would add MOISTURE IS ALWAYS PRESENT IN THE AIR.
06-27-2012 06:45 AM
deadbodyman I see this all the time ,The REAL problem is the primer that was used .Lacquer primer (spraycan primer) will do this every time because it allows moisture to soak in down to the metal making it rust...All that primer has to come off and the car needs to be stripped down to the metal(.you can do this in sections)Take care of the rust then use epoxy primer over the metal.You really need a compressor first and a DA sander the good primers only come in a can and need mixing then sprayed on with a paint gun...np sense doing anything until you get the basic tools you need...compressor ,Da sander, paint gun..
06-25-2012 07:13 PM
John long Search the forum for threads on Ospho. They are similar products. You will need to get the remaining paint off the car and really work the rustmort or Ospho into the rust If you really work it, it will disolve and remove the rust. CLEAN WELL with wax and grease remover and prime with a good Epoxy primer that will give it protection from moisture.

Good luck
John L
06-25-2012 05:49 PM
78 monte
Surface Rust/Rust Mort...teach me please.

I have allot of surface rust popping up through the primer on my car.And a large patch on the roof were body work was started and never finished(not me).
A freind of mine suggested I use rust mort on the car. I am limited on body tools etc.... as I nolonger have a garage or access to a compressor(DA etc//) just an electric palm sander and a dream(...or....nightmare???).
So what would be the best method of going about fixing surface rust.Do I sand as far down as I can get then rust mort???Rust mort then sand???
Any advice would be appriciated.
My goal at this point is just to stop the rust progression and cover the car in flat black primer. I can fix dents etc.... afterwards as I go.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.