Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Changing shift points in a GM 200R4 OD transmission
User Name
Password
lost password?   |   register now

Thread: Changing shift points in a GM 200R4 OD transmission Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-07-2014 11:10 AM
Fstarocka perfect! will be doing this mod when I pull the trans this week - pics and article saved on google drive!
07-05-2012 02:22 PM
willys36@aol.com UPDATE: I finally got a chance to drive the car. Prior to that I was taking my grandson's word for how it is shifting. The new governor is PERFECT! At light throttle it shifts @ 1800-2200rpm, right in the power range. At aggressive part throttle, shift points raise a few hundred rpm (2600-2800rpm), again right in the power range. I am confident if we needed full throttle acceleration, shift points would pop up to the right higher range.

In summary, the weight we trimmed as described above was perfect for our street setup.
06-26-2012 09:26 PM
willys36@aol.com Unfortunately the 200R4 has a totally different design governor from the 7004R. Whereas the latter has governor tuning kits and I think has access to the governor from the outside of the tranny, the 2004R has no tuning kits. You are on your own when it comes to tuning with no help from the factory or from tranny shops. You have to cut off mass from the weights by the cut and try method. The principles are the same though; NEVER adjust the throttle cable to change shifting characteristics on either tranny and lighten the centrifugal weights on the governor to raise the shift RPM.
06-26-2012 01:56 PM
rick 427 There were several factory gov weight and spring configurations for the 700,depending on the vehicle....I believe the 4cyl trucks and the corvette had the lightest weights....a TRANSGO calibration kit PN K61931S gives you several weight/spring options to adjust shift timing.
06-26-2012 10:46 AM
THERACER did you buy the recalibration kit and install the lightest weights ?
i have a 700r4 with a 4:56 and 31" tires with the same prob.

thanks , ROGER
06-25-2012 09:03 PM
willys36@aol.com
Changing shift points in a GM 200R4 OD transmission

When you upgrade to a 200R4 OD transmission to get the benefits of the 0.67 overdrive, it is rare that the automatic shifting sequence occurs at the proper speed. Most likely you have lower rear end gears and a cam so you want the shifts to occur at a higher RPM but the donor tranny is likely set up for a grocery getter and results in 1-2, 2-3 shifts way too slow for your setup. Thus you are stuck with manual shifting which is fun but there are times you want to set it in drive and run it automatically.

A lot of people suggest changing the shift points by adjusting the throttle cable. DON'T DO THAT! That cable needs to be set properly and left alone. It is the governor that sets the shift timing and you have to modify it.

Here is how we did it. Basically we cut down the weights on the governor which is the proper method.

We ended with perfect shift points for the street; ~2000rpm @ 1-2 and 3000rpm @ 2-3. We havent tried it yet but I assume at WOT the shiftw will rise accordingly to higher in the power band.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.