Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 1964 Chevy 327 Small Block Timing
User Name
Password
lost password?   |   register now

Thread: 1964 Chevy 327 Small Block Timing Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-08-2012 08:59 AM
cobalt327
Quote:
Originally Posted by 64Joker View Post
I'm interested in just "checking" my timing mark on my 64 Chevy smallblock, do I still need to plug the distributor vacuum hose? I don't plan on adjusting at this time!
Disconnect and plug it to check the initial advance (initial advance is the timing at idle). But the initial advance is not all of it- you really need to know what the total timing is (total timing = initial plus mechanical)- or else the engine can be damaged or have poor performance from detonation or insufficient advance at higher RPM.

To check the mechanical advance, use a timing tape or a dial back timing light and accelerate the engine until the mechanical advance quits advancing. The reading there is the total timing. The total timing for most SBC engines should be around 36 degrees, less for Vortec or 'fast burn'-type heads.

If you want to know how much the vacuum advance adds, attach the vacuum line to the vacuum advance and at idle take a reading. Disconnect it and take another reading. The difference between the two is the vacuum advance. Usually you need about 10-12 degrees from the vacuum advance. Stock vacuum advance cans often add more than that.

The combined advance (mechanical plus initial plus vacuum) should fall somewhere around 50 degrees under light throttle cruise conditions (engine vacuum high, throttle setting relatively low).

More on timing here, including how to make a timing tape and how to tell if the timing marks are accurate.
07-08-2012 07:23 AM
Mojo56
Quote:
Originally Posted by 64Joker View Post
I believe it would be "total timing"!?
Check the "static' timing by setting the idle RPM's to specs (about 550 RPM's) then disconnect the vacuum hose from the dizzy.

If you want to check the "total advance" leave the vacuum hose connected and rev the engine to about 3,000 RPM's and either read the timing light gauge OR what's on the timing tape/marks on the balancer (if so equipped).

Check the mechanical advance by disconnecting the vacuum and reving to 3K and reading the light or the timing tape.
07-08-2012 04:56 AM
hobbles Mornin 64Joker,
Yes, remove vacuum advance hose and plug the carb where it hooks to. Lower the rpm then check timing. If you have points, check the dwell first, then the timing mark.
07-07-2012 08:18 PM
64Joker
Follow-up

Quote:
Originally Posted by 68NovaSS View Post
Depends on what you want to check, total timing, vacuum advance, mechanical advance, initial, what rpm it's all in at, etc.
I believe it would be "total timing"!?
07-07-2012 04:47 PM
68NovaSS Depends on what you want to check, total timing, vacuum advance, mechanical advance, initial, what rpm it's all in at, etc.
07-07-2012 02:40 PM
64Joker
1964 Chevy 327 Small Block Timing

I'm interested in just "checking" my timing mark on my 64 Chevy smallblock, do I still need to plug the distributor vacuum hose? I don't plan on adjusting at this time!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.