Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 1958 biscayne
User Name
Password
lost password?   |   register now

Thread: 1958 biscayne Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-10-2012 08:42 PM
lilrobo thanks i sawthat video,, if i do that another motor is going in iwill win that way lol
thanks lol
07-10-2012 08:29 PM
Mojo56 58 oil pan removal - ChevyTalk --The Social Network for Chevy Fans


Never give up...
07-10-2012 05:00 PM
lilrobo well i gave up the oil pan won i put it back on i'll be ok till i do a motor swap of some sorts
thanks guys
07-10-2012 10:30 AM
lilrobo had an old man tell me i might have to jack the tranny up a little as well as the motor , i'll see this evening ,, i need a little luck
07-10-2012 10:07 AM
lilrobo its not the crank,, the pan is hitting the front of tranny
07-10-2012 07:05 AM
timothale
Crank

on some engines the crankshaft counter weights have to be up in a certain position.
07-10-2012 04:38 AM
lilrobo yeah i am doing research on the oil pan,, i dont see how it will come out, turning the motor isnt the problem , its hitting the tranny looks like it needs to go up about 2 more inches , it up now about 2 or more
got me
07-09-2012 10:15 AM
lilrobo i see , but my pan is hitting the tranny when trying to pull it out to rear
07-09-2012 06:53 AM
timothale
blocks , rotate

On some engines I used to put a piece of 2 X 4 between the mounts then have to use a wrench to rotate the crankshaft to wiggle the pan off, I don't know if that will work for your engine, some times I'v had to reach in with a wrench and drop the oil pump bolts and slip the pump- tube into the bottom of the pan. You might get more information on the chevy stovebolt forum.
07-09-2012 04:39 AM
lilrobo Well now what do i do? I dont want to spend alot of money on this motor,i just wanted to get it running, until this winter and maybe change it to v8 , i was told it would be cheaper to swap to v8 rather than rebuild ths 6 cl ?. I dont know now
*Thanks for the replies
07-08-2012 03:03 PM
lilrobo i almost have the pan out but dont see how it can come out ,, the main front member is in the way ,, i have jacked the motor all the way up,, i just dont know
07-08-2012 11:34 AM
Bryan59EC Most likely the engine has worn bearings----oil pump will probably not help.

As for a v8 swap-----all you need to do is locate and install
the v8 frame mounts for the engine.

I have heard the 6cyl mounts will work, but they place the engine too high
under the hood------and will most likely affect the driveshaft angles.
(which on the 2-piece shaft angles are important)

Also, if you go to an auto overdrive----you may have to raise the
rear of the trans quite a bit to maintain proper front shaft angles.

I have a 454 and a TKO 5-spd in my 59, ----engine bolted right in to the
stock v-8 frame mounts, but the trans x-member needed to be modified.

After a few years and nearing 10,000 miles, I will have to go back and:
remove interior
cut floor tunnel
raise floor tunnel
weld raised tunnel in place
lift the rear of the trans up to get an angle closer to 2* (now 4-1/2*)

Since you have a 58-----may not have the floor issues with a larger trans
that I have with the 59, but the length of any trans you use will affect the driveshaft angle.
My TKO is about 8" longer than the stock 3-spd so I'm pretty sure any trans you wish to install will be fine.

HOWEVER

A larger driveshaft or larger u-joints can present issues when installing.
That big ol Ford drive yoke on the front of my shaft has to be wiggled
thru the openings in the frame tunnel-----and once it is thru, there is very little space to wiggle it up to install into the trans.

Parking brake linkage may have to be modified as well, to avoid interferance with a spinning u-joint.
07-08-2012 09:44 AM
lilrobo well i check the oil pressure
cold is 40 psi
hot about 5
i guess i need a oil pump ????
07-07-2012 07:54 PM
lilrobo i took the total rocker assy apart and cleaned it ,i even clean the lifters too , i took them apart completely ,,i am getting oil to the rockers now , i see oil dripping from the small hole , i read the specs and the oil pressure is 35 psi,, not much, i did check it and had 40 psi i will check it tomm while hot and see what it is ,i just think the lifters are week they will pump up ,but lose it after sitting for a few min,, i adjusted them while th motor was running and got it sounding real good , but after sitting it came right back ,, i am doing research on what v8 is the best( easyest) to swap with, i will buy lifters for now but think about chaning this winter ,,,,,,

thanks for the info
07-07-2012 06:36 PM
timothale
6 cyl noise

My old chevy had oil flow problems, the oil passage way up to the rockers would plug up , we used to pull the rockers, poke a wire thru, use an oil can to squirt in some solvent, blow air thru. If the prev owner did not change oil often the inside would get gunked up .
And a swap to a Small block would be easy., They have an X frame so I don't know about late model OD trans fit.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:30 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.