|07-13-2012 10:00 AM|
|68NovaSS||On a different note...I changed the title of this thread to read SBC vs. sec, I assume that was your intent.|
|07-13-2012 06:49 AM|
You'd be looking at enough power to destroy a transmission too...
|07-13-2012 02:34 AM|
|Short-Bed Chevy||my cousin has a set of 327 heads that he is selling and he said them heads would make a 350 come alive because how big of ports it has on it. what do you guys think and thank you all for all the information you guys have gave me so far.|
|07-12-2012 09:31 PM|
what monte and AP said. Headers are probably the most important part of an engine build.Tube size and length are very important for max power or best throttle respones. The wrong headers can make your power go down and/or driveability suffer.
I had custom made step headers for my car because its special requirements needed that. In a low HP engine,small long tube headers are probably your best choice. All the parts matching is the most important part of the formula.Before buying random parts,research application and how if fits your requirements. Good luck and make sure that 100 mph pass is on a track
|07-12-2012 07:44 PM|
You cannot deny the effectiveness of these little roots style blowers as a great path to real street/truck performance gains. Especially in trucks that need a big big and streetable engine power/torque gain to get that big heavy truck moving.
And generally have lots of hood clearance
The (blower friendly) engine that goes under these blowers is actually pretty basic and needn't cost a lot to build.
A low compression ratio is key when using street pump gas.
|07-12-2012 06:02 PM|
Would you consider a 144 roots style under hood supercharger? You have the headers, gear, and overdive trans at stage 2 to back it up. I just rebuild and sold one for a little over $1200. Common to find good complete units under $1000. That is plenty left over for a cam/spring and carb purchase.
You would make a ton more torque and power than big heads and xr284.
My 85 c10 pictured has a 305 vortec 906 heads, Summit headers, and a new E force unit with performer cam. It is pretty exciting. Launches like frogs from a dynomite filled pond. 3.73 gear, dynamic 3000 stall, TH350c w RV level shift kit. .
|07-12-2012 05:12 PM|
Does this truck have to be emissions laws compliant?
What engine block are you starting with?
new w factory roller cam or older pre 1987 with flat tappet cam only.
You already have good long tube headers but what is the rest of the exhaust system?
|07-12-2012 04:53 PM|
|ap72||So you tried booking up a manometer infront of a muffler and didn't do more than make a mess? Headers are not used for exhaust flow, they're used for intake flow...|
|07-12-2012 03:13 PM|
Some people bolt on headers and claim magnificent gains. I never saw.
I have had the luxury to play with dynometers for a long time. Unfortuneately never really using them going past 6000 rpm. For me and hydraulic cams that seemd like a threshold for power . A wall if you pass there are serious expensive changes, first being fuel. 93 octane did not do any good past 6000.
Money is power and makes the power. That is also a solid truth. What are you doing and how far are you going. 100mph through the traps is not far.
|07-12-2012 02:32 PM|
|07-12-2012 02:21 PM|
Headers are one of the BEST parts you can purchase for your car, the next being everything behind them.
Get properly sized headers.
|07-12-2012 02:16 PM|
|Short-Bed Chevy||sorry about that i read it wrong|
|07-12-2012 02:10 PM|
|327NUT||He didn't say get a big block, he said get a big block TBI unit.|
|07-12-2012 02:04 PM|
|07-12-2012 02:02 PM|
|Short-Bed Chevy||So are you saying get a big block or get the big block tbi system sorry just got a little confused there|
|This thread has more than 15 replies. Click here to review the whole thread.|